Are you wondering how to fix a pressure washer hose? Then, we are the same but don’t you worry. We got a solution to this.
Pressure washers are a great way to clean driveways, sidewalks, and other outdoor surfaces. However, if the hose on your pressure washer becomes damaged, it can be difficult to fix it without knowing how.
It’s not always easy or possible for everyone to call in an expert who will come out and fix your problem right away. If you’re not sure what you’re doing, it might lead to bigger problems down the line that could cost more money than just getting someone else in there for you! So here are some quick steps on how to fix your leaking hose! Follow the steps explained explicitly below, and you shall get your hose fixed in no longer than 7 to 8 minutes.
Why Has This Even Happened?
Pressure washer hose has more than 800 psi of pressure built up inside, which is such enormous pressure and can cause damages to the hose by the time, those damages turn big by the time, and thus leakages occur.
Pressure washer hoses provide high pressurized water, as is evident from the name. This is done by electrical energy. High-pressure water removes dirt, paint, mold, and other things. Getting a new hose instead of fixing the leaked one can be expensive. Conventional methods of covering leakages through tapes are not of use as high pressure is inside the hose, which cannot be stopped through those tapes. And that tape methods could not be used for a long time solution. To fix the pressure washer hose in a reliable, safe, and professional way, you have to follow these given steps.
Tools Required To Fix A Hose
Before we move to steps, you need to have the following tools to get going with the procedure.
- Razor blade (to cut the hose from the leakage)
- Marker (to mark the leakages)
- A coupling (A coupling is what joins two parts of the hose)
- Wrench (Nut bolt tightener)
Steps To Fix The Pressure Washer Hose
The steps below will show you how to fix a pressure washer hose.
Step #1. Switch off the hose
The first step is to switch off the hose. This can be done by locating the valve at the end of the hose and closing it. This will stop the flow of water and allow you to work on the hose without any fear of getting wet. Remove the pressure washer from the electric socket or gas energy source and immediately unplug it; do not operate on it while connected to an energy source. This might be dangerous.
Step #2. Remove the water from a hose
If you are having trouble with your pressure washer hose, the first thing you should do is remove the water from the hose. This can be done by turning off the water supply and then disconnecting the hose from the faucet. Once the water is removed, you can inspect the hose for any damage.
Step #3. Locate the leakage
Leaks can be caused by a variety of things, so it’s important to identify the source of the leak before you try to fix it. Once you’ve identified the source of the leak, you can try to fix it. There are a few ways to identify the source of a leak on a pressure washer hose. One way is to look for bubbles. Another way is to look for wet spots on the ground. You can also try to listen to the sound of the water running through the hose. Once, you find out the leak, it’s time to mark it!
Step #4. Cut the hose
Cut the hose straight across the designated region with the sharp blade. Make sure you cut it over the leak spot and a little behind it. Use the knife with caution. Cut the hose on both sides because we’ll be joining them later, so cut both sides. It may also be a good idea to read about how to repair pressure washer hose.
Step #5. Get a coupling of your hose’s diameter and fix them individually
This is the crucial step because this step comprises selecting the coupling, i.e., the male part of it and the female part of it individually to the hose. As a result, you’ll need to obtain the appropriate coupling size to cover the leaking area. At this point, install the male repair coupling into the hose. It should be used only on one corner of the hose. Compression rings are used to secure the couplings. It’s time to start working with the hose on the other end. Attach the female repair coupling to the other end of the hose. The rest of the procedure is the same.
Step #6. Connect male and female coupling
After you’ve individually inserted both couplings, you’ll need to tie them together. The male and female couplings will be connected, and your wrench will be ready to use. Make sure the connections are securely fastened with your wrench.
Step #7. Connect back with the electric socket
Congrats buddy. You have successfully made it. But still, to get it back to work, you need to connect it to the electric socket. Connect and check if the leakage has been appropriately covered. First, analyze and check at lower pressures and then test it thoroughly and get going.
It’s A Wrap!
Learning how to fix a pressure washer hose was not that difficult right? Well, you got to make sure of something in the end. If your coupling is leaking again, this could be possible because you might not have tightened it well. If it is again doing the problem, then unplug the whole coupling and fix it again. This time it will be fine hopefully,
Click on these links to read related articles; know how to store pressure washer and how to use a pressure washer to remove mold and mildew.