Are you wondering why is my dryer keep blowing fuses? Well, no more wonder. We will assist you in fixing this issue. The most common reason for a thermal fuse blowing is blocked or limited air circulation within the exhaust vent.
Examine the lint screen for debris or lint that may be obstructing air movement across the dryer. In many circumstances, a faulty thermal fuse will prevent your dryer from turning on at all.
The drum will revolve, and the dryer will run in certain other dryer types, but the heating element cannot start to heat your laundry within the dryer because of the thermal fuse. Yes, my friends, it’s all true about it. So, if you are interested in this article and want to learn more, read this article carefully. Below, we have mentioned all possible causes of this problem. Let’s have a deep look at why a dryer blows the thermal fuses continuously!
Reasons Why Your Dryer Keep Blowing Fuses
Are you tired of changing the blown thermal fuses, and you don’t know why is my dryer keep blowing fuses? Alright, don’t panic. You might be struggling with one of a few typical problems if your machine starts breaking thermal fuses. Ensure that such thermal fuse just on the cutoff circuit or on the blower wheel on the radiator component is not gone when changing the fuse. We’ll go over some possible solutions and troubleshooting to help you resolve your issue.
#1. Check the blower wheel’s thermal fuse
The fuse on the dryer is meant to trigger when the level is too hot, protecting both the machine and the clothing. A multimeter calibrated on ohms (the resistance unit) can examine the thermal fuse. Check for thermoelectric circuit connectivity in between two junctions. Reinstall the thermal fuse if there is no connection. Inspect for dead threads and ends on all cables.
If you want to repair or replace the blown thermal fuse on your dryer, then the first step you have to do is to unplug your dryer from the wall socket. Also, keep in your mind that you have switched off the main power. Remove the top panel by removing the screws and put it away after you’re sure the dryer is disconnected.
#2. The relay on the control board isn’t working
The thermal fuse is a security measure in many contemporary dryers that shuts electricity to the heat source if it senses excessive heat. On the other hand, a defective circuit can sometimes trigger a thermal fuse. Inside this instance, the switch may become trapped in the on mode, preventing the thermocouple from receiving sufficient. Ignoring the thermostat’s indication to turn off the electricity, the heating element will continue to operate.
Because of this malfunctioning component, your dryer would not preheat and will continue running eternally. Whenever the system control switch sends power to the controller, this problem occurs. If the dryer is already on, it will transfer electricity, and if it is down, it will not.
The thermal fuse within the thermal component will burst whenever the dryer hits its threshold, cutting off the electricity towards the dryer. So because the circuit has become jammed, you’ll need to repair both the control board and thermal fuse. You may also read how to install a belt on a Maytag dryer and how to replace a belt on a GE dryer.
#3. Lint trap in the exhaust system
Whenever lint gets into locations such as the internal intricacies of a dryer drum, it may pose a risk and probably result in breaking and failures. Lint trapped within your exhaust system of a dryer might lead the thermal fuse to burn. The fuse will then blow out as a result of this.
There are some measures you could take if your dryer isn’t functioning. To begin, locate a lint filter beneath the duct and empty it of any lint. The next step is to look for a thermoelectric fuse around the air compressor. You’ll have to repair it once it’s burned out.
#4. Blocked dryer vent
A heat shutdown fuse may break when the dryer’s heating element gets too hot. This occurs when lint accumulates in the circulation system of the dryer, obstructing average air circulation. Inspect the rear of the dryer for any obstructions or lint accumulation to have it inside in working condition. The blockage might be as little as a strand of dust or as significant as nothing more than a stocking, but it is preventing the garments from drying correctly. Once you clean the clogged dryer vent, the dryer thermal fuse stops blowing out, and also you can dry the clothes properly.
It’s A Wrap!
We are happy that reading this article is just fun for you, and after reading this, you all will get the answer to why is my dryer keep blowing fuses. A clogged vent, lint in the exhaust system, and improper working of the control board are the primary sources of the blowing thermal fuses. However, after fixing these sources, you can quickly get rid of this issue. Thank you, friends, for being with us at the end, don’t stop sharing it with your friends! I also suggest you read here is why dryer keeps blowing thermal fuse.