Are you searching for how to install a belt on a Maytag dryer? There are five easy steps that you can try; these things I’m sure you can do with a breeze.
As you know, the Maytag dryer belt will gradually fade out like every equipment component. But even so, unlike many other dryers, you do not need to extract the plastic container to install the belt.
Therefore, you will indeed be able to use your Maytag clothes dryer again after you have learned how to install a Maytag dryer belt. Furthermore, you can install this belt without hiring an experienced appliance repair service or paying for labor. This is just an overview, so you better read further. Without further ado, let’s start!
Steps To Install A Belt On A Maytag Dryer
Whenever a dryer makes a noise associated with handling heavy items, it’s better to upgrade the belt. Use all these step-by-step guidelines to replace your belt and put an end to the screeching. Now, here are the steps on how to install a belt on a Maytag dryer:
Step #1. Remove the power supply
Before removing the cap, the very first stage is to unplug your dryer from the power supply. You could then remove your dryer from its panel (if appropriate) and begin working on it. If feasible, relocate the dryer to a location where you can easily control the back of the equipment. This involves removing the exhaust tube and uninstalling the electrical power if it has not already been completed. If somehow the dryer is pumped in with a thick metal nozzle or connected to the room’s electricity supply, you should rethink doing something like this yourself. To relocate the gas supply, do not try to release or detach it from any gas apparatus. Even a gradually leaking gas pipe is a hazardous situation that will ultimately initiate, potentially resulting in death.
Step #2. Take the front lid off
Detach the front frame mounting bolts from the inside of the panel with a bolt driver. Lift and detach the front frame from the two bottom frames by slightly pulling it forward. Remove the dryer’s front panel and keep it aside. Also, Examine the machine’s exterior close to the top about any outer fittings. Separating the upper edge accessible and easy, these dryers often have latching mechanism clips on the back and snaplock fittings under the upper edge. Extra bolts, generally neutralizing machine screws, should be checked at the lint filtration opening. You may also want to read about where to buy lid switch for a Whirlpool washer and where to buy lid switches for washers.
Step #3. Eliminate the barrel and clip the belt
Take care never to bend or try to pull the screwdriver in such a direction that it glides and smudges or harms the surface. Instead, raise the lid high to see the top of the dryer barrel when it is close to the locking ring. A slim shielded rubber belt must be covered all around the drum. If it is absent or highly loose, readers will have to replace it. If it has been on the barrel, you could have an issue with the motor that ultimately turned the drum or the electrical panels that regulate the dryer’s features rather than a belt problem.
There seem to be typically two contact pressure-type clips that best suit into a hole at the front panel, safeguarding the underside of the panel towards the edges of the machine, and trying to lift this part allows this to be eliminated so you can remove the drum. If lifting the front panel does not release it, look below the machine for hidden bolts or other fixings. If none can be found, try prying the front open. Click on this link to know how to replace a dryer belt.
Step #4. Wrap the drum with the belt
Examine the drum; there ought to be a symbol in which the old belt best suits the drum, and the new belt must be set in just the same position. Return the barrel to the device and help the front of the barrel to keep it in place. Then, Lie on the floor at the front of the dryer and inspect the elastic band and the motor controller that spins the drum beneath the barrel. Accommodate your new belt through the tensioner and across the motor roller, helping to ensure the grip tracks are undergoing the pulley correctly.
Step #5. Place the drum inside the dryer
Press the front all the way in, raising it across the locks and enabling it to fall towards them to protect the bottom in place. Next, insert the lid, assuring the seals fit nicely inside the barrel without being damaged. These guards are typically made of felt or another soft material and are kept in place with sticky tape. Consider replacing the screws that were excluded from disabling the front frame in the opposite order that separated them, and reconnect all electrical connections as you go. Allow the dryer’s lid to drop into place, then push to involve the snap locks at each edge. Check that all extra fittings have been replaced and are tightly fastened.
It’s A Wrap!
As now you have learned how to install a belt on a Maytag dryer, now you can do it on your own. Remember to keep the old belt and any dryer information to an equipment major manufacturer to match a substitute. Since some dryer manufacturers do not have older model repair parts providers, you may need to discover a supplier for your specific brand of the drying system.