How To Replace A Belt On A GE Dryer? 5 Easy Steps!

How to replace a belt on a GE dryer is a mandatory question to ask if your dryer is not starting. In five easy steps, you can, and these things you will know as you delve into this article further. We will tell a brief guide about the problems with the GE dryer belt and a complete procedure for its replacement.

Before everything else, let’s try to know how to figure out that the belt is broken or worn out. Suppose your GE dryer is not starting or giving humming sounds even after pressing the start button. Your dryer produces grindings like something, and the drum moves at high speed when you move it with your hand. It means that there is an issue with the belt inside the dryer. The strap is a drive or drum belt and can be replaced at home. There are more things that you should know, so without further ado, let’s start!

 

Steps To Replace A Belt On GE Dryer

Here are the steps on how to replace a belt on a GE dryer:

 

Step #1. Remove the control console first

Go to the back part of the dryer and remove the plug from the electrical outlet. Then you’ll see a metal plate on the rear aspect. Take your Philips screwdriver and open five screws. Lift the container out of the dryer and remove a ground screw that connects a wire to the plate.

Unscrew two quarter-inch screws from both sides of the console. Hit the panel from the back and lift it outside. Get the Molex strain reliever out of the board by pressing the tab. Take your phone outside of the pocket. Capture a picture to remember the configuration of relays. Then, start pressing the relays and pulling them outside of the panel. Make sure not to push the wires. 

You’ll notice four big and three small relays. Press the tab on the top side of the control console and remove the Wi-Fi connector wire. This is the last thing that you have to pull out to set the control console free. 

 

Step #2. Remove the top panel

Now it’s time to pull out the circular guards from each side of the top panel. You have to unscrew two quarter-inch screws each from a guard. Pull out both guards and set them aside. Now you have to deal with the wirings of the left circular guard. First, remove a ground screw connected to the dryer with a relatively long wire. Next, come to the right side and open a strain reliever that holds the wiring. Send down all the wires inside the cavity of the circular guard. Then open two Philips screws from the backside of the dryer. 

All done. Leave the backside and come to the front part of the darer. Open the door and search for two screws that connect the top to the front panel. Remove both screws with the help of a Philips screwdriver. You may also be interested to know how to remove the control panel from the Whirlpool duet sport.

 

Step #3. Remove the front panel

Also, remove the four screws from the top and bottom of the dryer to take the front panel apart after having done with the removal, close the door. Stand up and remove two quarter-inch screws from the top of the front panel. Now you have removed all the screws, set your drivers aside. Pull the front panel towards yourself and undo one wire harness on the top and two from the bottom to release the front assembly.

 

Step #4. Replace the drive belt

Now you are done with the removal of the top and front panels. Finally, it’s time to replace the belt. Keep reading to find out how you can replace a belt on a GE dryer yourself at home. Slide your hands below the dryer drum and feel two pulleys on the left side of the dryer. The larger pulley is named an idler and a smaller one as a motor. Pull the idler pulley towards the drum. Get the belt out that is held by a motor pulley. 

Be careful while doing all this. As you can harm your hands, wearing work gloves while repairing any appliance is recommended. You can also cut the belt with scissors or remove it from the drum without doing any of the above methods if the belt is already broken. Get the worn-out belt out of the dryer. Install a new one carefully in its correct place. Remember, the grooved side of the belt faces the drum, and the flat side will go with the idler pulley.

Set the belt on the downside of the motor pulley and come from the upper side of the idler. Keep setting the belt until it looks perfect. Rotate the drum to check if it is running smoothly and the belt is not coming off to its place. I guess it’s helpful to read about how to repair GE washer.

 

Step #5. Reassemble the dryer

Assemble the dryer again and make sure to connect every terminal and wire harness to its correct place. Also, be careful while screwing back all the Philips and quarter-inch screws. Attach every screw in the correct position and by using the specific screwdrivers. All screws should be firmly secured.  

 

It’s A Wrap!

Replacing a dryer belt is not a big deal in terms of difficulty. You have to follow some precautions and safety measures to complete the task successfully. Now you have detailed information about how to replace a belt on a GE dryer, and you are ready to fix up the issues. It may also be a good idea to read about how to install a belt on a Maytag dryer