How To Repair Air Bed Hole? In 5 Easy Steps!

How to repair air bed hole? Air beds use air as a form of support for sleepers instead of coil and foam.

It is also known as an adjustable air mattress.

Users can customize comfort by adjusting the amount of air in the chambers through the mattress.

Materials used in making air beds include plastic, rubber, and vinyl.

You can also deflate the air bed for neat storage or other outdoor activities like camping.

Air bed offers ideal comfort until you realize the mattress is slowly deflating, which disturbs your cozy sleep.

Good thing there are remedies you can do to fix holes in your air bed.

Locating the hole or leak in your air bed is an easy thing to do.

It is also affordable as you can purchase an inexpensive patch kit to cover the leak.

 

How To Locate Leak In An Air Bed?

Here are the steps for you to locate a leak in your air bed:

 

Step #1. It is natural to lose air

Consider the fact that no air beds can hold air the same amount of air forever.

Due to some reasons, it happens that air beds can lose air and you only need to inflate it again.

When your air bed is new, it needs time to stretch to its full size eventually.

The drop in temperature also causes the gas molecules to shrink, making them easier to escape.

 

Step #2. Inflate the air bed

If your air bed is shrinking at a faster rate, try inflating it.

Then try sitting or lying on the mattress to check if it sinks more than 2 inches.

If you are still unsure if there is any hole, set aside your air bed for a night after putting weights above.

Check the next morning if there is a significant difference in the size.

Continue inflating the balloon while finding the hole in your airbed.

 

Step #3. Stand the mattress on its side and listen for hissing sounds

It is preferable to stand the air bed on its side in a wide and silent room.

There are higher chances that holes are typically located underneath the air beds.

Move closer to your air bed and listen carefully if there are some hissing sounds.

Check the bottom first, then the sides and front.

 

Step #4. Wet your hands and hover them on your air bed

Moisturize your hand with water, then hover it in your air bed.

Maintain a distance of 2 to 3 inches.

The water in your hands will evaporate faster, making your hands feel cooler if there are leaks.

 

Step #5. Use water and soap

If there are holes, bubbles will form in areas where you applied soapy water.

Put small drops of liquid dishwashing soap in a small bucket.

Use a sponge to wipe the surface of the air bed.

Check first the valve, seams, sides, and faces.

When you locate the hole, wipe your air bed with a dry sponge.

 

Step #6. Mark and deflate

Encircling the leak can help a lot later when you start repairing it.

Use a pen or other water-based marker.

After finding and marking the hole, deflate the mattress.

Wipe your air bed with a dry cloth or towel, then set it aside for about two hours if you used soap water.

 

Steps To Repair Air Bed Hole Using Patch Kit

One option to repair holes on your air bed is buying a ready-to-use patch kit.

If the problem is a leaky valve, it is better to request a replacement from the manufacturer.

So, how to repair air bed hole?

 

Step #1. Buy an applicable patching kit

You can purchase patching kits online or in camping sections in outdoor stores.

A patching kit typically includes sandpaper, glue, patches for tents or mattresses.

Buy a patch kit that you can use in plastic or vinyl material.

 

Step #2. Deflate and sand

Make sure that the air bed is completely deflated.

Remove the flocking or soft coating in the area of the hole.

This will help the patch stick on the surface well.

 

Step #3. Clean the sanded area

Get rid of any dirt or debris in the sanded area using soapy water or a small amount of isopropyl alcohol.

Make sure that the area is dry before continuing.

 

Step #4. Cut and apply the patch

To completely cover the hole, cut about 2 centimeters of space around the hole.

Put glue around the patch, then gently apply it on the surface.

Make sure to dot it in the first try to avoid having a messy output.

 

Step #5. Put pressure, leave, and inflate

Press the area with your hands for 30 seconds.

Put a heavy and flat object at the top and leave for about 3 hours.

Inflate the air bed and place one ear on the patched area to check for escaping air.

 

To Sum Up

How to repair air bed hole?

Air beds use air as a way of support for users.

This type of bed is prone to puncturing and holes.

You can repair this leakage using available patch kits.

Repairing bed holes might be easier than you expect!

Thanks for your time!

Leave a Comment