Are you wondering how to remove pump from Troy-Bilt pressure washer? This article will guide you to increase your knowledge that will directly solve your problem. There might be hundreds of reasons to remove the pump from the pressure washer, sometimes it can be due to any fault, or other times, maybe you want to clean it.
Disconnecting the old pump from your washer is just a matter of a few steps. We are sure that you have the potential to complete this repair without any difficulty or mess with your pressure washer.
Before everything else, let’s know first what pressure washer pump is this. Well, a pump is attached underneath the pressure washer with the engine. The Troy-Bilt pressure washer has a vertical pump with three legs and three gas engine flanges. It has a built-in pressure control valve and chemical injection system. The start and thermal relief valves enhance the pump’s performance by making it safe and convenient to use. So, without any further ado, let’s jump right into it.
Why Is Your Pressure Washer Leaking?
There is one reason you are planning to remove the old pump, and that is leakage in your pump. But wait, there may be some other issue with your pressure washer, causing the leakage. These two main problems defect the washer system, and the leakage occurs as a result.
#1. A worn-out pump
Do you purge water out of the washer before using it? If your answer is yes. That’s an excellent practice, and everyone should follow it. But if you don’t do so, you have to make it a habit. Always purge the water by pushing the trigger gun of your pressure washer. Otherwise, the air stuck inside will damage the plungers, check valves, and unloader valve. All these are the main functioning parts of the pump, and if they become faulty, the pump will become faulty too. Leakage will be observed in your Troy-Bilt pressure washer, and replacing the old pump is the only solution to this problem.
#2. A malfunctioning thermal relief valve
As its name suggests, the thermal relief valve is intelligently designed to maintain the temperature snide the pressure washer. This valve could be a reason for leakage from the pump. But why? Because when you turn on the washer pressure, do not start cleaning your patio or home siding. The water inside the washer turns hot due to the continuous electricity supply. The thermal relief valve start emitting the water outside to let the cool water enter the pump.
What we learned is never leave your Toy-Bilt pressure washer running when not in use. This habit will not only prevent the pump from leaking but save energy too. But if, non-stop leakage is observed from the thermal relief valve. It may need to replace
#3. An old pump
The third reason for pump leakage could be a pump that has been used for a long time as we know that the life of appliances and their parts expires after serving us for years. We can give a new life to our pressure washer by simply replacing the pump after removing it. Here’s a definitive guide to pressure washer pumps.
Steps To Remove Pump From Troy-Bilt Pressure Washer
We listed a w easy-to-follow steps to make you understand the complete procedure of how to remove pump from Troy-Bilt pressure washer after figuring out that the pump is the main reason for leakage in your Troy-Bilt. Now you are ready to remove the old pump.
Step #1. Reposition the pressure washer
Disconnect high pressure and chemical hose from the pressure washer. Place the washer in a raised position like a table or a desk. Or, you can tip it down with the handle. The pump will become readily accessible in this way, making your work easier and more convenient. Remove the spark plug wire from the engine.
Step #2. Unscrew the pump
Find a nut driver of the correct size as the mounting bolt that connects the pump with the pressure washer from your toolbox. Start unscrewing the bolts from the lower side of the pump. Set the nuts aside after removal. You must be wondering why the pump is not coming out. The reason is it is tightly fixed with a key on the pressure washer, and it’s not just the matter of three mounting screws to remove the pump. You have to spray penetrating oil to lubricate the pump. Find out what kind of oil for pressure washer pump.
Step #3. Check the pump for any issues
Wait for 5 minutes after lubrication to let the pump absorb the oil. Then, wiggle the pump with a pry bar, and it will fall off with a bang. Now you can fix any issue with your pump. Whether to replace the whole pump assembly or the defective part that could be O-ring, check valve, or plungers.
Step #4. Get a new pump
When you are done removing the old pump and planning to replace it, make sure to order one after entering the correct model number of your pump or the pressure washer. This way, you will receive the same pump as the previous one. Here’s how to change pressure washer pump oil.
Safety Measures For Removal
Pick an outdoor location for your Troy-Bilt pressure washer, whether you are using or repairing it. There must be a free space of 5 inches from all sides to the pressure washer. This safety measure will reduce the risk of fire to a large extent.
It’s A Wrap
The answer to how to remove pump from Troy-Bilt pressure washer is far easier than your expectations. You need a nut driver and penetrating oil to start this repair. Fixing the appliances is satisfying. Isn’t it?