How to install Samsung gas dryer? Today, we’re going to dig deeper about gas dryers. We are more familiar with electric dryers and how to operate them. However, in handling and installing gas dryers, others need guidance to guarantee that they correctly.
Some homeowners would prefer having a professional install it.
You may, nevertheless, do it alone, but it would be best to have someone helping you. Keep in mind that you can be seriously injured if you don’t follow the directions precisely. We suggest you refer to your manual but it would take a while to read the long list written on it. That’s why we are here to help! Read on and you will learn how to install samsung gas dryer in no time.
Steps How To Install Gas Dryer
How to install Samsung gas dryer? The steps in installing Samsung gas dryers are similar to others. The only difference is that Samsung products have additional features, such as Wi-fi connectivity, lights, and more which make them distinct. Now, here are the steps on how to install Samsung gas dryer:
Step #1. Prepare
Gather all the needed materials and equipment. You may also refer to your manual about the parts of the gas dryer that you need to check if they’re complete. Also, keep flammable materials such as gasoline away from the dryer. Failure to do so can result in an explosion, fire, or death. Additionally, check if there’s an available electrical outlet near the back of the unit. Most manufacturers also recommend a dedicated circuit for the appliance.
The electrical supply should be about 120V at 60 Hz. However, they usually vary from one unit to another.
Step #2. Measure the area
Get your measuring tape and measure about 6 inches from the wall, and the unit should not be closer than this. Also, if you’re going to place it near a cabinet or another appliance, leave at least an inch between them for proper ventilation. Moreover, there should be enough space for the front door to open.
Step #3. Install leveling legs
First, let the back of the unit rest on cardboard for easy installation. Screw the leveling legs into the holes at the bottom of the equipment using an adjustable wrench. Adjust until the base of the legs is approximately half an inch from the dryer. After doing this step to all legs, return the dryer to its upright position and use a leveling tool to level all sides properly.
Step #4. Connect gas connector
Take note of the explosion hazards stated in the manual or by your manufacturers. One of these is tightening all gas connections. Moreover, have a qualified person ensure that the gas pressure does not exceed 330 mm water column.
Use a stainless-steel gas connector to connect the gas supply line and valve to the dryer. At the bottom back part of the dryer, there should be a pipe for the gas connector. Remove the cap first, then connect the gas connector with an adapter or pipe elbow. Use a pipe joint compound and an adjustable wrench to seal and tighten the adapters and connectors with each other.
Step #5. Check for gas leaks
Open the gas shutoff valve and check for any gas leaks in the connections. Spray a non-corrosive leak detection solution in the adapters and pipe elbows. The mixture will bubble if there are gas leaks. You should repair any detected leaks to avoid further damage.
Step #6. Attach the exhaust vent
The dryer should be exhausted outdoors to prevent fire. Before attaching the vent, there are also fire hazards that you should know, so don’t ignore the manual. For example, the exhaust vent should be heavy metal and not plastic or metal foil.
First, study the vent system chart in the installation manual. Use 4-inch diameter vents and clamps and 45-degree elbow joints for better airflow. The goal is to provide a continuous passageway for the air, so a few turns and joints would be perfect. Connect the vent to the exhaust outlet and use a clamp to secure it.
Step #7. Situate exhaust hood
This hood is where the other side of the vent will blow out the air from the dryer. The location should be on the exterior part of the wall where it will direct the air towards the environment. However, it should not be that far to avoid stretching out the vent. Also, the hood should be 12 inches high from the ground.
Step #8. Insert rubber washers
This step is only applicable for dryers that use steam. First, turn off the cold water faucet and disconnect the washer inlet hose from the faucet port. Remove the old rubber washer from the hose and replace it with a new one. Also, in the provided 2-foot and 5-foot inlet hoses, insert a rubber washer into both their ends.
Step #9. Connect the hoses
First, attach the 2-foot inlet hose to the faucet port and the other end to the single part of the y-connector. On the one y-connector port, connect the washer inlet hose, and on the other side, the 5-foot inlet hose. Make sure to use pliers to tighten the couplings but avoid overtightening.
Step #10. Connect the hose to the fill valve
First, remove the protective cap of the fill valve on the dryer’s upper rear panel. Thread the 5-foot inlet hose onto the valve and tighten. Turn the cold water faucet on and check for leaks in the connections. Lastly, move the dryer to its final location and ensure that the hoses and cords are not kinked.
To End
And that is how to install Samsung gas dryer. Please keep the manual that comes with the product as it contains specific instructions for installing the unit. Moreover, we suggest you call a professional to install the Samsung gas dryer for you to save time.
Regardless, learning new things on your own is still a good choice. Atleast you get to do things on your own and save money from paying others. We hope you learned something from the 10-step article we presented you. For more helpful guides, you might be interested in these articles about how to light a gas dryer and how to replace a gas dryer. See you next time!