The question is: how to clean a water heater burner? Well, cleaning the water heater burner assembly required a few steps, which you’ll learn as you further delved into this article. A heater burner coated with smoke and dirt would not warm your water more efficiently, increasing gas use. However, a gas-fired hot water tank has a few technical problems.
Regular cleaning increases the appliance’s life and keeps it running at top performance.
Cleaning the water heater’s tank every year will eliminate insulating silt between the interior of the tank and the combustion process and maximize heat transmission. After 3 to 4 months, cleanse the main burner head and ash vacuum soot from the combustion chamber. It will help you burn cleaner and save money on gas. If you want to learn more, keep reading this article at the end. Let’s have a deep look at it!
Cleaning A Water Heater Burner?
How to clean a water heater burner? You can clean the burner on the hot water system within a few steps, which requires minimum effort. In less than an hr, you must be capable of completing the cleaning. If you have any issues with these maintenance works, see your use and care instructions.
#1. Turn off the gas supply
You should turn the water heater off—the gas control valve, to be exact. Next, turn off the supply of gas from your water heater by closing the gas shutoff valve. While you’re cleaning the burner, this one will smother the spark inside the water heater & keep it from switching on. Let the combustion process cool by opening any doors or windows to guarantee adequate ventilation.
#2. Remove the burner assembly
There should be an orangish wire connecting to the bottom side of your water heater’s gas valve if it is labeled “White Rogers.” The piezo lighter in the combustion chamber is attached to this wire. Keep the orange wiring inside the door structure and remove the wire lead. Disconnect the igniter valve terminal out from the bottom of the ignitor switch using a wrench if your water heater seems to have a “Robert Shaw” gas valve. From the base of the gas valve, you may now unscrew the three various sized hex-head connections.
The thermopile or thermocouple will have one, the pilot gas supply will have another, and the central burner will have perforated piping. You may take each one out with a counter-clockwise twist of an adjustable screwdriver. When you remove these gas supply lines, a small quantity of trapped gas within the tubing will be released. If you feel a gas smell for a short time, don’t be frightened; the small gas will shortly dissipate.
Check whether the gas valve is completely sealed if the smell of fuel remains.
#3. Remove the burner assembly by sliding it out
Slide the burner tubing and assemble it out of the combustion chamber well with a loosened or uninstalled combustion barrier. Go gently and cautiously to avoid damaging any seals, disturbing any dirt, or snagging on almost anything. On the other hand, you might want to learn how long does a pool heater lasts before you continue.
#4. Start cleaning
Once detached from the hot water system, the burner component may be readily cleaned using a vacuum cleaner and a soft-bristle brush. A vacuum with a brush adapter does short work of almost all carbon accumulation and particles! Set that vacuum within the combustion chamber afterburner assembly has been cleaned clean.
Thoroughly vacuum the combustion chamber, along with the flame aerator beneath the burners. If the hot water tank has intake air filters, wipe these to remove any dirt or particles. Dust bunnies clinging to the burner might stop it from receiving sufficient clean air, resulting in a slow flame. You’re prepared to reassemble all, and now it’s immaculate!
#5. Reassemble the burner
Replacing the burner assembly in the combustion chamber should be the primary procedure. You can use any mounting guide, bracket, or slot on the rear of the combustion chamber to guide a burner assembly all into place. It could require a few tries and several delicacies to line all correctly.
Step #6. Install the combustion door
Check the inside gasket of your combustion door regarding signs of damage and strain. If necessary, replace it. Put the combustion door back into place and secure this with the fasteners you pulled before. Fasten the bolts in a grid formation to guarantee that the door is tight and appropriately sealed.
Step #7. Restart your water heater
After doing all the above steps, it’s time to turn on your water heater and suspect leaks.
On all of the gas pipes you’ve established, you can apply a leak detecting remedy or Windex. You may need to relight the pilot light and switch on the gas control valve. Verify that the burner has re-ignited and is heating your water tank. Put a little leak detection liquid to your gas valve fittings and inspect any air bubbles that indicate a gas leak when the burner is burning. You may also be interested to know about the best garage heater.
It’s A Wrap!
After reading this article, we hope you all understand how to clean a water heater burner. We have discussed seven simple steps for cleaning the burner quickly. Click on these links to read related articles; know how to turn on a pool heater. Thank you, friends, for being with us at the end!