Are you worried about how to clean a concrete step without a pressure washer? No more worries, you have arrived at the right place. There are many techniques to clean concrete steps without a pressure washer, like using a detergent, vinegar, brush, and concrete cleaners.
You can take some water, add soap or another detergent, mix them well and rub your concrete steps with a brush, sometimes it’s hard to clean concrete steps by hand using these detergents, but if you want your actions to look neat and clean, you have to do work hard for it.
Before cleaning your concrete steps, wear gloves in your hands and wear a mouth mask to avoid any infections; try to clean your concrete steps in the day so you can clean your actions well. Then, let’s get closer to it!
Steps To Clean Concrete Steps
Concrete steps may be cleaned in several ways. First, remove stains off your concrete stairs with a bar of moderate dish soap and a stiff bristle brush for mild spots and inside cleaning. You can also use a concrete cleaner with a pushing broom for difficult stains and outside chores to clean your concrete stairs properly. If you think your steps are still dirty or stained, do all the procedures two times for better results because concrete is complex and cannot be easily cleaned. Before starting cleaning the concrete steps, use safety gloves and a face mask to avoid any dust allergy. Read the below-mentioned steps carefully to learn how to clean a concrete step without a pressure washer:
Step #1. Clean sweep the concrete steps
You should clean concrete steps with the broom and remove all solid waste like wrappers, mud stains, or dry leaves. Next, sweep dirt and debris off the concrete steps with a brush. Sweep the steps until dirt and debris are gone. This will get the concrete ready for cleaning. Conversely, a leaf blower may be used to clean the steps of dirt and debris. Know how to clean concrete steps without pressure washer.
Step #2. Use soap and vinegar
Dish soap in liquid form should be used. In a plastic bucket, blend all ingredients until they are thoroughly incorporated, after adding one part vinegar to make the mixture more powerful. The water must have a temperature of 104 ℉ (42.5 degrees Celsius). Find out how to use soap with pressure washer.
Step #3. Pour the solution over the stains
Keep in mind the solution has thoroughly covered each spot. Allow ten to fifteen minutes for the answer to settle. Make sure the solution doesn’t dry out while it’s setting. If the stain begins to dry, pour additional solution upon it. If the discoloration is particularly tenacious or older, let the solution sit for thirty min.
Step #4. Scrub the stain with a stiff bristle brush
Avoid using a steel scrub brush since it can harm your concrete. Using a scrubber, scrub the spots until they are entirely gone. If the stains persist, use a powder laundry detergent to sprinkle it. Allow ten to fifteen minutes for the detergent to work. After the time has passed, saturate the stains with hot water and brush them with a firm, stiff brush until they have been entirely gone.
Step #5. Rinse with hot water
Rinse the stairs well with heated water unless all detergent residue and dirt are gone. You may have to wipe your steps 2 to 3 times. The water should have a temperature of 104 ℉ (41.5 degrees Celsius).
Step #6. Mix boiling water and oxygenated bleach in a mixing bowl
In a plastic container, blend all ingredients until they are thoroughly incorporated. The water should have a temperature of at least 106 ℉ (41.5 degrees Celsius). Instead of using oxygenated bleach and water, you may use a specifically made concrete cleaner. These are available at the local manufacturing unit.
Step #7. Spray the concrete steps with a mixture
The solution should be poured into a tank sprayer. Then, spray the solution onto the stairs from top to bottom, concentrating on the discolored areas. Allow 15 – 20 minutes for the answer to set once you’ve coated the entire surface. To prevent the mixture from drying out although setting, ensure the concrete steps are well saturated. If the solution begins to dry, re-spray the steps with an extra explanation. A tank sprayer is available for purchase or rental at your hardware store shop.
Step #8. Scrub the steps with a long-handled brush
You may also do this with a push broom. Brush the steps from top to bottom till the dirt and grime are entirely gone. Clean tiny gaps and corners using a small scrubbing brush. To avoid a patchy appearance, be careful to wipe the stairs equally.
It’s A Wrap!
We are delighted to know that you have learned all about cleaning concrete steps without a pressure washer; read all the steps mentioned above carefully on how to clean a concrete step without a pressure washer. Take preventive measures before starting cleaning the steps. Thank you, friends, for sticking with us! I guess it’s helpful to read about how to clean brick and concrete with a pressure washer.