The question is: how to install a stackable washer and dryer in a tight space? There are a few steps involved in stacking these machines, and you’ll learn them as you further delve into this article!
These giant machines might be inconvenient. However, this is among the most effective ways to free up space in your house without sacrificing an essential item.
Installing a stackable washer and dryer in a small area may drastically increase the amount of space available in your house. Stacking these appliances saves space and allows you more flexibility in where you put your clothes. So my friends, if you are interested and want to learn step by step guide, continue reading this article until the end. Let’s get started!
Steps To Install A Stackable Washer And Dryer In A Tight Space?
Below we have listed some steps that will help you how to install a stackable washer and dryer in a tight space;
Step #1. Measure the area
The first step is to take measurements of your equipment and the limited space available. Appliances must be smaller than the available area, with at least two inches of clearance on all edges for protection and simple hose and cable installation.
Furthermore, the dryer and washer must not be pressed against the rear wall, leaving just a few inches of clearance behind them. Finally, remember to compare the space’s height with the combined height of both units. Check for a water faucet or drainage system before moving anything. You won’t be able to connect up the machine without a water line.
Step #2. Place the washer
Begin by placing the washer in the desired location. Because this equipment is enormous and weighty, you need to enlist assistance. Because the washer is so much heavier than the dryer while it’s in operation, it always sits at the bottom of the stack. Note that the washing machine is full of water. Even though there isn’t a significant weight differential now, there will be whenever the device is turned on.
If you’re going to put the washer in a tight spot, ensure you have accessibility to the rear of the machine because you’ll need to connect it. Check for straightness using the level. Adjust the feet till it is. The washer’s level is critical. Because the dryer will rest on it, it will tremble and shake throughout cycles if the washer isn’t level. The dryer may shift and topple as a result of this instability.
Step #3. Place the stacking kit on top of the washer
This is a simple procedure. Make sure the stacking kit is aligned correctly on the washer. If your kit contains an integrated shelf, ensure the front is somewhat protruding so that you can take it out. If you’re not sure, go to the manufacturer’s instructions.
Step #4. Take out the dryer’s feet
We can start preparing the dryer once the washer is in place. Remove the feet from the dryer before stacking them on top of the washer. This makes it possible for the dryer to fit within the stacked rack. Keep the dryer feet stored securely in case you use them again.
Step #5. Attach the dryer to the washer
Place the dryer on top of the washer with the aid of another person. Ensure that the dryer is securely attached to the appliance. The last point you need is for the dryer to topple, so don’t release until you’re confident it won’t shake or wobble.
Step #6. Connecting the machines
You may start fastening them together now that the stack is straight. First, check the stacking kit’s instructions on connecting the devices. Then, the appliances are securely fastened together, fasten the screws, and secure the brackets. This is best accomplished with the adjustable wrench.
Step #7. Connect the hose and the cords
You may now safely stack the washer and dryer and reconnect the cables, and vent lines drain hose. Begin by connecting the dryer’s vent lines and the washer’s drain hose, following the manufacturer’s directions if necessary. Because it may fit in a confined space, the dryer vent will most likely be a periscope vent.
You’ll also be required to use foil tape to cover any gaps between the vent and the wall. You may now connect the machines after these are in place. You may also be interested to know about washer and dryer problems you’ll regret ignoring.
Step #8. Perform the final test
That’s it. Run a test load before you pack up. This prevents the equipment from swaying during operation. It’s better to test everything now rather than wait till you have your first cycle of clothes. Check that the machine is level if it is shaking.
It’s A Wrap!
Finally, we’ve answered you: how to install a stackable washer and dryer in a tight space. This is a simple method that might help you organize your laundry area. You can save space by stacking these machines. When installing a stackable washer dryer in a tight space, the essential things to note are providing enough airflow and utilizing the proper stacking kit for the units. Thank you, friends, for being in touch with us! You may also want to read about washer and dryer in one how does it work and how to store a washer and dryer.