How To Drain A Pressure Washer? Easy Steps To Follow!

Are you wondering how to drain a pressure washer? The methods differ regarding gas pressure and electric pressure. But with an electric pressure washer requires you to get a bucket filled with tap water, and put a suction hose into the bucket while you attach the garden hose, so turn it on and position the gun as it sprays water for two minutes.

Pull the trigger after the garden hose is disconnected and store the device indoors. The gas pressure washer follows a step-by-step process to get a fuel stabilizer and remove the water and detergent inside the pump system.

How to drain a pressure washer

Add some fuel stabilizer inside the gas tank and operate the engine for several minutes. Remove the cleaning solution and water and get a bucket of clean water. Hook the garden hose in a pressure washer and put the detergent tube feed onto a bucket filled with pure and tap water. After pulling its trigger with a nozzle at low pressure, allow it to operate. Turn its hose off to follow, remove the inlet, and pull the trigger again, draining the system’s water. Lastly is to position the pump saver in a pump inlet. So, read the article further!


Steps To Drain A Gas Pressure Washer

Be extra careful when gas appliances are stored in gas pressure washers. But remember that any gasoline or combustible stored in your home for a long time should require removing gas inside the tank. Next is to move it away from the potential igniter; it’s dangerous; it’s still best to store the pressure washer in a similar building where you stay and sleep. Below is the guide when draining the gas pressure washers.


Step #1. Getting some fuel stabilizer

Store the pressure washer properly if you aim to safeguard the engine and not use it for the next 30 days. Get some fuel stabilizer and remove the water and detergent from a pump system.


Step #2. Adding some fuel stabilizer

Add some fuel stabilizer inside a gas tank while operating the engine for several minutes, fully circulating in the entire system.


Step #3. Removing the water

Next is to remove the cleaning solution and water inside the pressure washer, so grab some bucket filled with tap and clean water.


Step #4. Hooking up the pressure washer

Hook up the pressure washer to the garden hose and put the feed tube for detergent inside the bucket filled with tap and clean water. Pull the pressure washer’s trigger using a nozzle in low pressure and allow it to operate for several minutes, cleaning it off of detergent. Next, turn its hose off while removing the device from the inlet.


Step #5. Pulling the trigger again

Pull the pressure washer’s trigger again while you drain its water inside the system.


Step #6. Adding a pump saver

Add pump saver against freezing in pump inlet, in the area with temperatures that drop to freezing. Do so to help safeguard the pressure washer against mineral deposits and cold temperatures.


Steps To Drain Electric Pressure Washer

An electric pressure washer helps remove the requirement of using gasoline protective measures. You only have to handle the pump system promising storage for the long-term.


Step #1. Getting a bucket of clean tap water

Grab some bucket and fill it with clean water.


Step #2. Placing a suction hose onto a bucket

Put a suction hose onto a bucket filled with clean water, attach the garden hose; turn the device.


Step #3. Turning on the pressure washer

Turn on the device while the gun you need to hold and spray water to last for two minutes, thus clearing detergent off from the system.


Step #4. Getting garden hose disconnected

Get the garden hose disconnected while you pull the gun, emptying the water into the system.


Step #5. Storing the device indoors

Keep the device indoors and safely position it in a lovely spot, thus preventing any seal damage or freezing. Add some pump saver against freezing inside the pump outlet, safeguarding internal seals.


Draining A Pressure Washer Is Always A Good Idea

Learning how to drain a pressure washer is always a brilliant idea. It cleans the drain of possible residues, dirt, and debris, as it is common for plumbers to clean gutters and remove potential buildups and blockages. Thus, it helps minimize the chances of a blocked drain since your pipes may always have a problem of being frail, causing unwanted further damage to the lines.

Avoid an expensive venture, consider plumbing inspection that drains a pressure washer completely. If you’ve got old bars, and won’t withstand pressure in cleaning off using a pressure washer; opt for relining pipes to ensure the longevity and stability of drainage pipes. You may also be interested to know about how to avoid pressure washer problems.


It’s A Wrap!

Now you learn how to drain a pressure washer, gas, or electric. Follow the step-by-step guide when draining a gas pressure washer and an electric pressure washer. Always consider doing it as it’s indeed a good idea. Even plumbers suggest using it to clean drains and remove dirt and debris! Share this info with your friends and family for their know-how! You may also want to read about how to release pressure from pressure washer and what is pressure washer pump oil.

Leave a Comment