Are you wondering how to connect a pressure washer gun to garden hose? You’ve arrived at the right place, so don’t be worried. You can use your home’s water supply to connect your garden hose to a pressure washer, but you’ll need a second hose to connect the pressure washer to the pressure spray cannon.
The second hose should be rated as a pressure washer hose, capable of handling at least 2700 PSI. On the other hand, most garden hoses can barely withstand 300 to 500 PSI. Depending on the pressure washer, this pressure might range from 1000 to 6000 PSI. To connect your pressure washer gun to your garden hose, you’ll need a hose mainly made for high PSI. Let’s take a closer look at it. Let’s begin to read this article!
How Does It work?
The installation and dismantling of your pressure washer gun will be a snap with these connectors. A single set of connections connects your spigot and garden hose. The third set of connections links your high-pressure hose to your pressure washer pump, and a fourth pair connects your garden hose to the pressure washer. A tie for connecting your spray gun to your high-pressure hose is included in certain sets.
Steps To Connect A Pressure Washer Gun To Garden Hose
Though hooking a hose for the garden to a pressure washer may appear to be a simple procedure, it may be difficult and unpleasant at times. With the correct gear, though, you can learn how to connect a pressure washer gun to garden hose in no time. We’ll teach you exactly how to achieve that in this article. Let’s get this audience involved.
Step #1. Measure the Gallons Per Minute (GPM) of your water supply
The type of connection you make between the pressure and your garden hose is determined by what you’ll be using it for and how often you’ll be using it. The first step is calculating the rate at which water runs through your faucet. It may be calculated in gallons per minute. Because most pressure washers demand a 3 gallon per minute water supply, your water source should be able to produce three to five gallons in a single minute. Put a 3-gallon pail under your faucet and time how long it takes to fill it to determine the GPM of your water supply.
Repeat the procedure three times more to determine the average time it takes your water supply to fill a 3-gallon bucket. A 3-gallon bucket can be used to supply water to a power washer if it takes less than 60 seconds to fill it to the brim.
A low GPM water supply can damage pressure washers. Most pressure washers require a flow rate of 2-3 gallons per minute. Fill a 3-gallon bucket and time how long it takes to fill it to determine your flow rate.
You can use that water supply for your pressure washer if it fills in less than a minute. Don’t neglect this step since a lack of flow might cause the pressure washer to break down.
Step #2. Connect a splitter
A splitter might be an excellent tool for you if you plan to utilize your pressure regularly. It saves you the time to unhook your garden hose after each use. While you can open the other valve of the splitter while operating your pressure washer, limiting the GPM of water going to your pressure washer. If you don’t like to unplug your regular garden hose from the water supply every time you use your pressure washer.
Although you may run your garden hose and pressure washer simultaneously with this split valve, you should avoid it since your GPM will drop below the 2-3 GPM necessary to run the pressure washer. Whether you use the split valve or not, you’ll need to connect your water supply and garden hose using a fast attach connector. This will let you rapidly disconnect your pressure washer from the water supply, allowing for more straightforward interior storage.
Step #3. Connect the water inlet with a garden hose
The next step is to connect the garden hose to the water inlet on your pressure washer. Ensure that the connection is secure and that there are no leaks. Connect the other side of your garden hose to your water source after that. Check for any leaks and double-check the connection. If any leaks occur at the connecting sites, you must locate a fitting to stop the leak. You may also want to know how much water does a pressure washer use.
Step #4. Attach the wand of the pressure washer to your garden sprayer
The pressure washer hose must then be connected to the wand or spray gun. After that, attach the other side of the pressure hose to your power washer’s water output. A shorter hose will assure a greater PSI while maintaining the flow rate required to feed the power washer appropriately.
It’s A Wrap!
After reading this article, we were ecstatic to learn that you would all understand how to connect a pressure washer gun to garden hose? We hope you read this article in one sitting, so if you want to join a pressure washer gun to a garden hose, attempt to remedy it on your own. Thank you for keeping with us, friends! You may also want to read about how to start a craftsman pressure washer and how to start a pressure washer.