The Easy Way to Fold a Bob Motion Stroller

The Bob Motion Stroller is a wonderful stroller for kids who are ready to move past the traditional umbrella fold. This article will show you how to fold and store your bob motion stroller.

If you’re going on a vacation, or if it’s just too hot outside, there may be times when you need to put your Bob Motion away. Follow these steps carefully to ensure that your baby can enjoy their next ride in style!

Bob Motion Stroller

 

Steps on Folding BOB Motion Stroller:

Step 1. Lay the stroller out flat in front of you with the wheels facing away from you. Grabbing the seatback, pull towards yourself and pivot it until it is resting on its side with one wheel up off of the ground. This will be your first fold.

Step 2. Fold the other three sides so that they are touching each other – do not close this yet! Then grab both handles at one end to bring them together for a second fold. At this point, all four corners should now have their corresponding corner folded underneath them.

Pinching these together tightly can help ensure that your final product has no gaps or creases along any edges where material may slip through undetected when closing more securely later on if needed.

Step 3. Now fold the adjacent side, and then do this to all of your remaining sides in succession.

Step 4. When you have done this for every single side, make sure that there are no gaps or creases visible anywhere along any edges – if so, close more securely by bringing one corner over top another on either end where necessary.

Once you’ve crossed off these potential holes/crevices with material from opposite corners meeting at a point, tuck both handles up inside each other towards the centre line of the stroller body (where they cross). The final product should now be a square bundle shape sitting upright like how it looked when first folded into its initial position!

 

How do you fold a BOB stroller car seat adapter?

The first thing you want to do is unfold your frame until all four wheels are out in front of it – there should be two on each side. Next, find where the straps attach around either wheel (they may not have them).

Unsnap these buckles with one hand while holding onto the handlebar with another by pressing down on the bar near the top and pushing outward on the handlebar at the bottom simultaneously. With both hands-free, grab any strap end that has an unfastened buckle and bring it around to the other side of the wheel.

Next, find the straps that have an unfastened buckle on either end – these should be in a pile at one large hole on each side near where you were holding onto the handlebar. Bring any strap end up from its corresponding bundle, wrap it gently over the top of the wheel and then back under itself to make a loop with this new piece before pulling tightly.

Repeat this process for every loose car seat belt buckle without letting go of frame or bar!

 

How to put the front wheel on a BOB stroller

Assemble the stroller with the handle and seat in a standing position as if you were about to use it.

With one hand, grasp either side of the wheel and pull down on them so that they are at an angle from the ground or “hanging” towards you.

Next, place your other hand under where these two pieces come together (the part called a headset) and push upwards hard enough so that this area is now above both hands below it whilst still holding onto both sides of the wheel which should be angled downwards away from each other.

Now carefully release your right-hand grip slightly while continuing to hold the left end firmly by pulling down on it until there is more slack between how tight things are around its wheels.

 

How to fold a Babyhug stroller

Step 1. Place the rear wheels on a raised surface like an ottoman, you can also use a platform or table that is not too low.

Step 2. Push down on the front wheel until it locks into place and then pulls up to release the seat from its locked position. This will allow you to lift off of one side before setting it back down again without needing two people for assistance with completing this process.

Step 3. From here wrap both arms around the folded frame to prevent it from tipping over when lifting upwards carefully following where each limb goes and how tightly they are wrapped together (as pictured below). Now grasp underneath where all four arms come together and lift upwards.

Step 4. Once the frame is lifted off of the ground, pull outwards on each arm so that it pops open as pictured below to allow for a larger area to be unfolded with less tension being imposed upon its joints while doing this process.

Step 5. Now unfold one side at a time by pulling apart from where they are connected until you reach how much space can fit your desired length when fully opened before repeating with however many remaining sides remain unopened (as seen below).

Finally, hold two handles tightly near the wheels and push down on them simultaneously to release any tension being held onto by metal springs or other parts which may cause folding difficulties due to tightness during transport.

 

Leave a Comment