What Does f70 Mean On A Whirlpool Dryer? 4 Easy Steps To Fix The Error!

Are you wondering what does f70 mean on a Whirlpool dryer? Stop wondering, and start reading this article. This F70 Error Code indicates that the user interface panel and the central control boards cannot interact. This implies that when you try and set the dryer, its message is not received by the main control board, and the dryer will not operate correctly.

This F70 error number most likely causes issues with the touchscreen panel’s interface to the main control panel. The F71 Error number appears on some models to highlight this problem.

what does f70 mean on a Whirlpool dryer

It typically indicates a significant issue that cannot be fixed. However, not all situations are irreparable. However, on specific models, F71 appears instead of F70. Keep reading this article to improve this error code on your Whirpool dryer.

 

Steps To Fix The f70 Error Code On Whirpool Dryer

The F70 error code on a Whirlpool dryer shows that the user interface board and the Main Control Board are not communicating. The below mentioned are the step-by-step guide to know what does f70 mean on a Whirlpool dryer and how you can quickly fix it.

 

Step #1. Attempt a dryer reset

Attempting to reset the Whirlpool dryer seems to be a fine place to begin. That’s because the error code may appear as it shouldn’t, in which case a simple reset would resolve the issue. To reset a Whirlpool dryer, follow these steps: Cut the power for one moment. You can turn off the socket or turn off the breaker. Turn the supply back on again and attempt to get it to cycle within 1 minute. If indeed the problem code persists, proceed to the following action.

 

Step #2. The user interface board should be replaced

Its user interface panel would be a printed circuit board that interacts with the digital display or control board knobs to guarantee that the dryer does what you want. A user interface board may wear out or short out due to the power surge. It may be destroyed if it comes into touch with water and the dryer gets excessively hot. It is not possible to fix the board when it becomes faulty. A user interface board may be replaced: Switch off the dryer’s electricity. You can turn off the wall and turn off the circuit breaker.

Take the upper access panel by unscrewing a few screws that hold it in place. Identify the user interface board, which is located underneath the control center. Remove your control panel bracket after you’ve found it. Start by removing the board’s electronic plug before removing the panel. After installing the latest user interface board, reconnect the cable connection and the mounting bracket. Reassemble the dryer and see whether the situation has been fixed. Otherwise, move to the next phase.

 

Step #3. Examine the connectors just on the mainboard

Another possibility for an F70 error number on a Whirlpool dryer is faulty cables linked to the control board. The connections might get rusted and stop functioning over time, or they can get loosened in rare situations. Here’s how to inspect the links on the control board: The dryer should be turned off. You can turn it off to access the control board and detach the access panel. Find the control panel and ensure the connectors on both ends are secure. 

Tighten things if they’re loose. Look for any indications of corrosion just on connectors. These will have to be updated if they have deteriorated. Proceed to the next phase if they are good. After replacing the connections, turn on the dryer to see if the situation has been fixed. Otherwise, proceed to the next phase.

 

Step #4. Its central control board should be replaced

The primary control board functions as the dryer’s intelligence. It instructs all of the elements in the dryer. The dryer may cease operating when it becomes faulty, or the F70 error code may appear. For a variety of causes, the primary control board may be malfunctioning. It might be due to natural damage, or it could be caused to an electric shock or heat flow damage.

Updating its main control board is costly and does not ensure the dryer will function correctly again. You could be better off buying a new dryer instead of repairing its main control board, mainly if the dryer is old somehow. If you prefer to change its main control board, follow these instructions:

Ensure that the dryer’s electricity is switched off. You have the option of turning it off or turning off the breaker. To access the main control board, detach the access panel and find the control panel. Remove the connections and remove the screws which keep the controller in position.

Detach the outdated control board and replace it with the new one. Reassemble the links and screws. Reassemble the dryer and check whether the problem code has vanished and the dryer is now operational. You may also be interested to know about common causes for a whirlpool dryer not starting.

 

It’s A Wrap!

Congratulations, you have learned what does f70 mean on a Whirlpool dryer. This error comes when the connection between the main control board and the user interface board fails. You must fix this error code by following the steps mentioned above, but you need to call a professional if you are still confused. Thank you, friends, for staying with us. You may also want to read about why is my dryer taking so long to dry and how to tell if your dryer vent is clogged.

Leave a Comment