A Step-by-Step Guide to Putting Together a Quinny Strollers

Quinny strollers are a great option for parents that want something light and portable, but still roomy enough to comfortably fit their child. They are also easy to fold up and put in the trunk of your car when you need to take a trip somewhere.

Putting one together can be quite tricky if you don’t know-how, though. That’s why we have created this step-by-step guide on how to assemble the Quinny Zapp Xtra Stroller!

Quinny strollers

 

Step on Putting Together a Quinny Stroller

Instructions:

Step 1. Insert the seat into the car base. Make sure that you do not fully tighten it in just yet, as this can be done later on.

Step 2. Slide one of the struts into each side panel where they should fit – these are found by either loosening or tightening slots with a screwdriver (depending on how your model is assembled).

Step 3. Tighten all screws gently to keep everything together and then adjust any excess fabric so there aren’t any loose threads sticking out. Tuck them back inside if possible! You’re now ready for use!

 

Tips: Quinny strollers come in many different models depending on how much space you need when folding up the stroller, how lightweight you need it to be, how much storage space you want the stroller to have or how many children can fit in your Quinny.

Newer models include features such as sensor lights which show when your baby may just need some extra warmth but still needs to sleep in the fresh air outside or if your baby needs a nappy change.

Not all Quinny’s come with rain covers but if you can find one that does, they provide great protection from the elements for your little ones – even when it is windy or raining because these are made of fabric rather than plastic.

 

How do you Disassemble a Quinny Buzz?

The Quinny Buzz is made up of five different parts which come together to form the pushchair. You must take your time when assembling and disassembling the stroller as it can be quite fiddly at first, but once you get used to how it goes together then it becomes second nature.

Step 1. Remove the head unit from its position overhanging above the handlebars by unscrewing a single bolt on each side with a spanner or screwdriver. The two bolts are located behind plastic covers which need removing before they can be accessed – this will cause them to pop out slightly so make sure not to drop these during assembly!

You’ll see four small holes just underneath where each wheel meets the frame, which is how you’ll know they’re the correct ones. The bolt will unscrew from here and can be removed by turning it clockwise with your hand or a spanner/screwdriver

Step 2. Take note of how the head unit was positioned before removal, as this will help to remember how to place it back on when completed – once again using a screwdriver/spanner turn in opposite directions until both bolts are screwed back into the holes at each side. Again make sure that all plastic covers have been replaced beforehand!

Step 3. Now take out two sets of four screws located underneath where the seat meets the frame by removing them firstly with either hands or pliers; these need loosening carefully so don’t apply too much pressure on them.

Step 4. Ensure that you have a clear view of how and where the seat should be slotted in before doing so, this will avoid it going back on incorrectly or at an angle that can cause damage to your stroller!

 

How to Disable Quinny Buzz Xtra

For a Quinny Buzz Xtra, there is one plastic cover; for all other models there are two – take note of how they were positioned when removed during dismantling as these need replacing too (not forgetting any screws!).

Step 1. Slide the seat into place making sure not to forget either set of bolts underneath once again. Ensuring that both sets match up with their respective holes by sliding through from inside outwards while screwing tightly after each bolt has been inserted fully.

Step 2. The metal brackets should be at the front of the seat and not facing out (please make sure to refer back to how they were positioned during dismantling too!). Slide both sides into place, ensuring that all bolts are tightened securely.

There is one plastic cover for each bracket on either side – these need sliding in from inside outwards while screwing tightly after each bolt has been inserted fully. Finally, push down firmly onto the top of each bracket so it clicks into position before moving onto the next step!

Step 3. Now slide up the hood as you would when using your stroller normally with a space beneath it where the baby’s feet will go; this could also serve as storage for other items if required! Push down firmly on any clips or buttons to ensure they are locked in place.

Step 4. Create a seat by placing the back of one of your stroller’s seats on top of the frame and then clicking it into position using up arrow buttons; make sure this is at an angle that suits how you intend to use your Quinny!

Step 5. Now slide down hooking straps onto each side, where there will be clipped together once the baby is inside their new ride (and also allow for quick release if needed). Slide hooks under the hood strap so as not to scratch or damage any surfaces while pushing them outwards from underneath.

Now clip together both hooks into a crossed shape, pulling upwards firmly with two hands until tight enough.

Leave a Comment