Are you wondering how to level a washer? There are three commonly used methods in leveling a washer. It would be best if you found the better option for your washer’s capacity.
Washers have been a convenient machine that will help us do the laundry without getting too tired. Sometimes, the weather isn’t suitable to wash clothes and of course, having a washer with a dryer is a bonus.
There are various brands of washers in the market, but there isn’t much difference in leveling these machines. Between the metal and plastic legs, plastic legs can be level faster, but you must handle them well. Continue reading all these steps in this article, and it will help you obtain a carefree washer and make it spin as it was before. By leveling your washer, you will also prevent the washer from further damages, for sure. So, without further ado, let’s start!
Ways To Level A Washer
Are you troubled by your washer that isn’t level? Does it affect the way your washer spins, and you are searching for alternatives that will help you? Learn these methods with caution.Every washer has adjustable legs, but usually, it will depend on how modern or old the model is. Some washers have metal, self-leveling, and manual legs. Identifying your washer’s leg portion will hint at what method to use by leveling. You can use the spirit level tool to check the level. Here are the ways on how to level a washer:
#1. Adjust the washer into a shorter leg
Adjusting the legs little by little is simple than pulling off a higher portion. This way, you will have to change it by moving up or going down slightly by little. It will also prevent you from repeating. Washers used for a long time can be unsteady, and they can be prone to breaking leg/s.
#2. Place a spirit level on a flat surface
A spirit level is a tool used to level a surface and determine if it isn’t. It has three tubes, which the vertical, horizontal, and diagonal. Place the spirit level into the flat surface of the washing machine. If the surface is flat, the bubble in the horizontal tube will move to the center.
#3. Adjust from one or two legs at a time
Know that if it’s your first time adjusting a washer’s leg, you might find it difficult. Try to change the adjustments for each leg or either two legs from both sides. Do not apply so much pressure in adjusting, as it might bend or, worst, break.
#4. Adjusting the self-leveling rear leg
Probably, your washer belongs to the modern washers. The self-leveling rear leg or automatic rear leg are much easier to handle than the manual. You only need to lift the back of the washer by about 2.5 cm, and it will automatically adjust. If you noticed that the self-leveling machine didn’t level itself, try tapping the back legs with your wrench or pliers, as it is for possible rust, and lift it again.
#4. Adjusting the manual rear leg washer
This washer is mainly with the older model, and the person must adjust the legs manually. You can identify the manual washer directly, as it has locking nuts or grip points. By leveling this kind of washer, locking nuts and grip points must be adjusted. It is better for manual rear leg adjustment from front to back. Prepare a wrench or pliers, and examine the locking nuts or grip points. Directly, lose the nuts in small portions and adjust them, and repeat as necessary. Be careful not to tighten the nuts hard as it would be harder to lose them again or break.
For easier adjusting, you can use a block of wood to keep the level as you set. Then, use the spirit level to and watch the tiny bubble. The bubble will determine if your washer’s leveled well.
#6. Rock or shake the washer
The machine spins around, and the legs are the foundation of the rotation of the washer. To ensure that the legs are strong enough and well-balanced, you must rock your washer with minimal force. You don’t have plans yet to buy a new one right now, eh? If your washer were with metal legs, try to lose the locking nut first, using a wrench or pliers located at the base. Adjust the locking nut and rotate it counter-clockwise until it reaches the bottom of the washer. The locking nut will serve as the lock between the leg and the washer.
For those washers that have plastic legs, you will need pliers or a wrench to get a hold of it. If you’re using pliers, pull the handles to the broader size and then hold it on the washer’s leg. Turn it clockwise if you want to lengthen it and counter-clockwise for shortening. Be mindful that expanding the washer’s portion is longer as it is more prone to bending and breaking than the metal legs.
It’s A Wrap!
Now, that’s how to level a washer. Leveling your washing will absolutely prevent you from buying a new one or creating additional damages to your devices. The steps indicated above can help you to balance your washers. The washer’s leg is as important as the other parts of the machine.
There are several brands of washers in the appliance stores. And it is essential to buy a machine that will meet your needs and can last longer. Checking appliances before paying is a vital part of the customers, and it’s better that you accompany a person who is capable of inspecting them. But, some stores test the appliances to make sure there are no problems with them.
Suppose you failed to balance your washer after many attempts and applied the methods. Maybe you need to remove the parts of the washer’s leg and replace them.
On the other hand, if you are not knowledgeable enough and still have doubts about following the step-by-step procedures, you can contact a repair shop for assistance or ask for a home service. Read related articles; know what is the biggest washer size and where to rent washer and dryer. Until here, my friends!