How to fold up Graco tottlytots playpen? The Graco tot lot playpen is a great way to keep your baby safe and secure. However, you might be thinking about how to make it small enough for storage or travel.
This article will show you the best method for folding up this particular model of playpen so that it can fit in any bag without taking too much space.
If you’re planning lots of trips out with your newborn then read ahead as we have some tips for storing this product as well as using it! Just follow these easy steps.
Step by step guide: How to fold up Graco Tottlytots PlayPen
Step One – Fold Up Side Rails First. You need to first fold up the side rails of the playpen. They should be flat against each other and then just stack them on top of one another until they are a nice compact size that can fit into any bag or storage space you have at home.
Step Two – Roll Up The Mesh Netting. Now it’s time to roll up all of your mesh nettings inside out so it forms a long tube. Once again, this is going to make for an easy way to store as well as transport around with you!
You might need some help from a partner here if you want someone else holding onto the end while you do most of the work rolling but either way, it’s important not to fold too much because we still want a room in there for the next step.
Step Three – Fold Playpen Mattress. The playpen mattress is a bit bigger than the netting and rails so you’ll need to fold it in thirds lengthwise before rolling it up as you did with the mesh. This will take up more space but it’s still essential to include so your baby has a comfortable place to rest while inside the playpen.
Step Four – Place All Folds Together. Now that everything is folded up, but all of the items are together in one big pile. You should now have a small, easy-to-carry package that can be stored just about anywhere! Make sure you label it well though in case someone else needs to use it or if you forget what’s inside.
Step Five – Set Up Playpen. Now that you have your playpen all packed up, it should only take a couple of seconds to set everything back up again! Just undo the zips on each side and open out the mesh netting so it’s square once more.
Next just pop both ends onto their corresponding poles and secure them with locking rings before pushing down gently until they lock into place too.
You can then place your mattress wherever you want but make sure there is some space for airflow between where people are going to be standing or sitting while playing etc. Once done, get ready for lots of fun time spent together as a family!
How do you assemble a baby pen?
The first step is to gather all of the materials that you will need for the project. This includes the following items:
-Sixteen panels of wood, each measuring 24 inches by 48 inches
-One panel of wood, measuring 24 inches by 72 inches
-Paint or a sealant in your desired color scheme
-Ruler or a straight edge
-Circular saw
-High-density foam insulation
-Staple gun and staples
-Cordless drill with a Phillips head bit
Once you have gathered all of the necessary materials, it is time to begin assembling the baby pen. The first step is to cut panels of wood down to size. Use a circular saw to cut the panels down to size. You will need sixteen panels that measure 24 inches by 48 inches and one panel that measures 24 inches by 72 inches.
Next, you will need to paint or seal the wood in your desired color scheme. Be sure to allow the paint or sealant to dry completely before moving on to the next step.
Once the paint or sealant has dried, use a ruler or a straight edge to draw lines across the panels of wood that will serve as your guide for cutting with a circular saw. Use a circular saw to cut along these lines, making sure to keep the blade parallel with the straight edge.
You will also need to cut out four sections from each of the panels that measure 24 inches by 48 inches. These sections will be used to create the corners of the baby pen. Use a jigsaw to cut out these sections.
Next, you will need to drill holes in the panels that will serve as your entrance and exit points for the baby pen. Use a cordless drill with a Phillips head bit to drill these holes. The holes should measure approximately two inches in diameter.
Once all of the pieces have been cut, it is time to start assembling the baby pen. Begin by stapling the foam insulation to the back of each panel. Be sure to staple it securely in place so that it will not move around once the baby pen is assembled.
Next, line up two panels of the baby pen with the straight edge facing up. Staple them together securely to create a seam that runs down the centre of each panel.
Repeat this step until all sixteen panels have been stapled together along their seams, creating two long walls for your baby pen.
Once you have created your first two walls by lining up and stapling pairs of panels together, line one 24 inches by 48 inch panel on top of these wall sections so that it is resting flush against the inside edges.
Be sure to keep it as even as possible when doing this so that there are no gaps between any pieces. Use staples or nails to affix this piece in place across its entire length, making sure not to miss any spots where the panels meet.
Do the same thing with the other long wall, using a panel that measures 24 inches by 72 inches in place of the one that measures 24 inches by 48 inches. This will create your top and bottom walls for the baby pen.
Now it is time to attach the two end walls to the top and bottom walls. Use a jigsaw to cut out four sections from each of the panels that measure 24 inches by 48 inches.
These sections will be used to create the corners of the baby pen. Attach them to the top and bottom walls using nails or staples, making sure they are evenly spaced and lined up correctly.