The Complete Guide on How to Disassemble Pack and Play Bassinet

The Pack and Play is a bassinet for babies that folds up to be easily transported. The bassinet has many parts, but it’s fairly simple to take apart once you know-how. This guide will show you How to Disassemble Pack and Play bassinet step by step.


disassembling a pack and play bassinet

Steps on How to Disassemble a Pack and Play Bassinet

Step 1 Remove the mattress.

Step 2. On either side of where the bassinet meets the pack n play frame, two screws need to be removed using a Phillips head screwdriver. 

Step 3. The top layer of fabric should completely detach from underneath once all four screws have been removed.


Steps on How to Attach Graco Bassinet Leg Caps

Step one: Remove the leg caps from their packaging, and remove any plastic covering on each cap.

Step two: Position the rubber side of the bassinet leg caps against either corner of your Pack N Play’s metal frame (see diagram above). The grated texture should be flush with that of the metal bars.

Step three: Using a Phillips head screwdriver, tighten screws into holes at bottom corners until you feel resistance (make sure not to overtighten). Repeat the process for opposite legs if necessary. Congratulations! You’ve successfully attached your Graco baby crib leg covers.


How to Assemble a Graco Dream Suite bassinet and Changer

Assemble bassinet frame – To get started, you have to attach the four legs of the base. For this step, you will need a Phillips head screwdriver and an adjustable wrench if your model has leg extensions.

To assemble the standard size Graco Dream Suite Bassinet, turn over the plastic package containing all hardware pieces onto a flat surface such as a floor or table (see diagrams above).

Place each leg on top of its corresponding joint piece until it clicks into place (see diagram below for how they should look when assembled correctly). If using an adjustable wrench for this step instead of a Phillips head screwdriver make sure not to tighten too much so that there is still some movement in the joints.

Attach two legs to their corresponding leg caps by aligning them so that they fit into each other (see diagram below for how they should look when assembled correctly).

These pieces will require a Phillips head screwdriver and adjustable wrench if your model has leg extensions. Place one of the screws on top of each cap, then press down with your forefinger while holding onto the base of the cap using your thumb and pointer finger.

Repeat the process until all four legs are attached to both leg caps. Make sure not to tighten too much so there is still some movement in these joints as well. It may be helpful at this point to have someone else hold up one end you work from where you’ve attached the legs.


How do you fold up an Uppababy stroller?

The first step is removing hoods/canopies if they were not already taken off before the folding process started (recommended for best outcome). 

the second step is grabbing both handles on either side and pulling upwards until it locks into place in how far you can go with your arms straightened out above your head. 

The third step requires sitting down by bending your knees so that your feet touch the floor and your hands are holding the stroller in how you want it to sit. Using your feet, push yourself back a little bit so that the weight is on them and not all with your arms.

Now use both hands to pull up with one of the handles until the desired height is reached or if you do not have enough strength for this step then just continue using your feet as mentioned above but instead pulling upwards from underneath sides with heels while keeping toes planted on the floor. 

The fourth step requires starting from the same position with how far legs can be stretched out straightened ahead of self and bending knees into half-squatting down position where calves rest against fabric surrounding top framing pieces of the frame where stroller has been folded up in how much room there remains inside width wise.


What Kind of Crib Mattress do I Need?

When deciding what type of bedding will suit your bassinet best, make sure not to overlook the size and shape factors.  

Your baby may look cute in any one piece outfit but several other elements should also be taken into consideration when choosing their sleeping arrangements.


How to Clean a Baby Trend Bassinet

Cleaning the fabric used in various parts of your baby trend stroller is not difficult.  It can be done with regular home products and does not require much time or effort. Steps are simple, just follow them carefully for best results.


Steps on How to Clean a Glider Rocker Bassinet

Step 1. Take off the cushion and wash it in soapy water

Step 2. Wipe down all painted surfaces with warm soapy water.

Step 3. Remove hardware from wood components then spray them thoroughly with clear gloss enamel paint. Finally, reassemble the glider rocker bassinet after.

Leave a Comment