5 Simple Steps on How to Assemble Your Graco Stroller

This article will walk you through how to assemble your Graco Stroller step by step. You have just purchased your new Graco Stroller and are eager to get it out of the box.

You can’t wait for that feeling of accomplishment as you put together this beautiful stroller, but how do you know how to assemble a Graco stroller? If you’re like most people, then the idea of putting something together might seem daunting. There’s no need for fear!

 

Steps on Assembling Your Graco Stroller:

Step 1. Remove the Graco Stroller from its box and layout all of the pieces. You should be able to see how each piece is labelled with a letter or number, so take note as you organize them in alphabetical order according to their corresponding letters.

Step 2. Take the two wheels (labelled “A”) and attach them to both sides of your stroller frame using one peg per wheel on opposite corners. Now that these are secure, move on attaching the four leg posts which will hold up your baby’s seat if it has been purchased separately from the base unit…

Once those legs have been attached (two on either side), add another set of pegs for added stability on top for an even more sturdy feel.

Step 3. The next step will be to attach the two posts which will hold up your baby’s seat if it has been purchased separately from the base unit. These are labelled “B.” They fit into slots on either side of the frame and can only go in one way!

Step 4. Next, place both back wheels (labelled with a “C”) onto their respective pegs at either end of your stroller frame…

Step 5. Finally, you’ll need to put four rubber caps onto each wheel as they won’t work without them! You should have enough for all eight wheels so that none can accidentally fall off during use.

 

How to put the front wheel on a Graco stroller?

Next, place the front wheel (labelled with an “E”) onto its respective peg at either end of your stroller frame. It should fit snugly and not move around very much. If it is too tight, try spinning it in the opposite direction to loosen up the rubber on both sides before trying again!

Finally, you will need to put four rubber caps onto each wheel as they won’t work without them! You should have enough for all eight wheels so that none can accidentally fall off during use.

The number one rule when putting these on is making sure there are two per side–one right next to the other!–so that they stay securely fastened and don’t pop off while you’re using your stroller.

Now your stroller is ready to be used!

 

How to Remove a Graco canopy stroller?

Step 1. First, lay the canopy stroller down flat on a firm surface like your floor or a table.

Step 2. Next, remove all of the screws from both pieces that hold the canopy to the side of the frame with a screwdriver (most canopies have four). Do not worry about how many are in each piece — you will need to take off them all eventually so it does not matter how many there are initially.

Step 3. Once you’ve taken out all eight screws for one side and set aside those two large plastic washers also found under these legs, pick up this now loose end where the fabric meets metal and pull until it is free from what remains on either side then flip over so that other leg’s screws are now exposed.

Step 4. Remove all of the screws from this other side with your screwdriver then remove these washers and repeat what you did before by pulling each section free until it is completely detached.

You should now be left with two large pieces that are the same size as when they were assembled, but without any metal, legs attached to either end or fabric hanging off them – how easy! Now just put the canopy back on in place of those feet (make sure parts A go into sections B) and reattach both sides using only four screws at one time for each leg set/side.

They’re labelled so do not worry about which goes where. You may need a partner to help hold up one side while another attaches its matching screws (which will also require you to use a screwdriver).

 

How do you put the wheels back on a Graco stroller?

Step 1. First, place a rubber cap on each wheel to ensure no damage occurs during transportation.

Step 2. Next, attach both back wheels onto their respective pegs at either end of your frame – they only go one way!

Step 3. Finally, screw them tightly with an Allen key for maximum stability and performance. Congratulations on assembling your brand new Graco Stroller! Now enjoy its many features (see above).

 

How to fold a Graco click Connect stroller?

Step 1. First, make sure you have tightened the strap on your Graco Click Connect stroller handle.

Step 2. Next, fold one side of the frame to meet with the other – it will lock in place securely.

Step 3. Finally, pull up and release both sides simultaneously so that they are folded flush against each other. Congratulations on folding your brand new Graco Stroller! Now enjoy how easy it is to transport or store away (see above).

 

How do I unfold a Graco click connect stroller?

Step 1. To begin unfolding your Graco click connect stroller first remove any objects from between the two frames then press down firmly on both ends at once. The two frames should snap apart automatically into an open position.

Step 2. Next, fold one side of the frame to meet with the other – it will lock in place securely.

Step 3. Finally, pull up and release both sides simultaneously so that they are folded flush against each other. Congratulations on folding your brand new Graco Stroller! Now enjoy how easy it is to transport or store away (see above).