Do you know how to replace heating element in Whirlpool dryer? This article will assist you in understanding the heating element replacement. The first step is to cut off the power supply of your Whirlpool dryer for safety concerns, open the access panel screws with a screwdriver and safely find the heating element.
When you find the heating element pull off the thermostat wires and replace the heating element.
When your dryer won’t dry your clothes properly, your dryer’s heating element was the only culprit, so you should replace it immediately to avoid any delays in the drying cycle. Well this is just an overview, replacing a Whirlpool dryer heating element is a simple but dangerous task, so you need to follow the below-mentioned steps to replace it correctly.
Steps To Replace Heating Element In Whirlpool Dryer
As a little overview above about the replacement of heating elements, you need to follow these steps to learn how to replace heating element in Whirlpool dryer.
Step #1. Turn off the power supply
Electronic parts are used in every step of this procedure. To keep everybody safe, unplugging the device from its power supply must be the first move.
Step #2. Get to the back panel
Pull the unit away from the fence once this is disconnected so that you can access the back of it. To reach the rear parts, remove the screws surrounding the back panel and take the top off.
Step #3. Take away the component
To begin, disconnect the thermostat’s cables. Snap a photo of the cables which clearly shows in which each wire belongs when you install a new component to ensure that you restore them to the right ports. With such a flathead screwdriver, pry the wires out from the blocks. Once the cables have been removed. Remove the element from the heat pipe by unscrewing it and taking it down or apart.
Step #4. Set up the new component
Loosen your thermostat first from the old component then move this to the fresh one just before installing the new component in the dryer; a fresh thermostat also isn’t supplied. Simply pull the terminal free, remove the thermostat from the tab, and place it on the replacement element. Its terminal is then snapped into position. Push the replacement element into place so that the screw openings line up and it fits neatly into the gap. Retighten all screws after that.
Step #5. Assemble the dryer again
Reconnect all three wires to a thermostat or element using the photo you picked up earlier. Fasten the rear panel into place before pushing the dryer back into alignment.
Whirlpool Dryer Heating Element Overall Cost
One must spend approximately $160 to $270 for a replacement heating element, including materials and labor. For labor, an appliances specialist usually costs around $70 and $110 per hour. Just one service charge is also included in this price. Service prices for most technicians range from $55 to $85. A replacement heating element might cost anything from $45 to $100. Depending on the type of dryer, this item could cost anywhere from $35 to $220 or more. You may also be interested to know about troubleshooting whirlpool dryer problems and repairs.
What Is The Average Life Of Whirlpool Dryer Heating Element?
The heating element inside a dryer is what heats the dryer so that the garments may be dried. If indeed the dryer is only used once in a while, the heat source should survive as long as a well-cared-for dryer, that has a life expectancy of 7 to 17 years.
Dryer heating components do not always survive as much as the dryer structure, and continued use may necessitate replacement before such a fresh dryer is required. These components may be purchased from a variety of manufacturers and retailers. The dryer heating element has no defined lifetime but can be burned out every time if a dryer gets too hot or the ducts get blocked.
A heating element inside a dryer can last around 7 and 17 years when it is maintained well and also the venting or lint traps were cleaned properly. A heating element in a dryer that is used every day and not carefully maintained might be burned over at any moment. Cleaning the lint filter before another load is the best method to keep the dryer in good working order; otherwise, lint may start building up and go into the vents.
This not only clogs the vents and increases the burden on the heat source by requiring it to warm to a greater degree, but it also poses a fire threat. When the dryer is turned on, it takes air in via a blower wheel then passes it through the heating element, and warms it. The garments will not dry when there is inadequate air or if obstructions prohibit the warm air from being released, and the element may overheat.
It’s A Wrap!
We are delighted to know that you have learned how to replace heating element in Whirlpool dryer. You need to follow the steps mentioned above to replace the heating element. The average life of a heating element is just about 7 to 17 years if you maintain things well. Thank you, friends, for staying with us. You may also want to read about how long does dryer take to dry clothes and laundromat dryer how long.