What To Do When Hot Water Heater Is Leaking? 5 Easy Steps!

With time your hot water heater starts leaking the water, there are many reasons for this problem, but have you ever wondered what to do when hot water heater is leaking? Noticing a water puddle near your hot water system is the biggest problem.

That’s new chaos to wipe up, and the terrible sensation you have when you think about how much cost you’ll spend to remedy it is disgusting. If there’s a puddle at the bottom of your hot water system, it’s crucial to figure out what’s wrong so you may not have to deal with any further issues.

what to do when hot water heater is leaking

We’ll discuss some of the most frequent causes of leakage, how to repair them, whether they’re minor or require water heater service, and how to avoid this problem from recurring in this post. You may have to hire an expert to repair your hot water system. Perhaps all it needs is delicate care to restore it into operating shape. Therefore, here are some options for dealing with a leaky heater; let’s get started!


Steps To Do When Hot Water Heater Is Leaking

Users never have to sit powerless and perplexed in front of a leaky water heater. Please read for some straightforward step-by-step methods to fix this problem. Here’s what to do when hot water heater is leaking: 


Step #1. Ensure that your water heater is leaking

Finally, it’s the moment to address the root of the issue.  It’s crucial to determine if the water is caused by a leak rather than condensation. There’s no need to be concerned about condensation. Essentially, it implies that the hot water tank is extremely hot, yet the space in which it is installed is extremely chilly.

Clean up and sanitize your hot water system to see whether it’s the case. Then examine it from the outside. Condensation is most probable if moisture appears uniformly over the surface. Inspect the gadgets in the area after that. Would your air conditioning unit be adjacent besides? Check to see if the source of the leak is your air conditioner or heater. To determine where the water is flowing from, place a towel on the floor.


Step #2.  Switch off the electricity

After you’ve confirmed that the leak is coming from your water heater, switch off the electricity right away. While your water heater is connected to its source of power, you must avoid operating on it. Locate your circuit breaker and turn off the hot water system switch if you have an electrical water heater. A dedicated gas shutdown valve is located near the gas line at the bottom of a gas water heater.


Step #3. Turn off the cold water supply

Next, turn off the cold water supply to your hot water system. The top of your water heater tank has two pipes connecting to it. A shutdown valve on most water heaters’ cold supply input pipe. That’s wherein you get your water. The cold water entrance line, often marked by a cold for blue and hot for red, feeds cold water to the water tank.  

The hot output line carries hot water into your house from your hot water system. If pipes aren’t color marked, you can tell which ones are cold and hot by feeling them. Turn the shutdown valve clockwise as far as possible if it’s a wheel. Turn the knob 180 degrees if that is a ball valve. You may also be interested to know about the potential reason cold water isn’t coming out on your faucet.


Step #4. Investigate the water leak’s cause

So it was time to get serious about our work. It’s time to locate the cause of the leak so that you can properly diagnose and fix it after your power and water sources are switched off. Inspect and wipe up any areas where water accumulates. If you observe a buildup of water in a similar spot the following morning, you remember repairing your leaky hot water system precisely.

Is there a water leak coming from your water heater’s top? Examine the two pipes at the water heater’s top. The cold water intake pipe and the warm water output pipe are known. These lines transport water from the tank to your residence, which will be heated. This might cause your leak if its connections or couplings are faulty. A pipe wrench can be used in this scenario to adjust the pipes.


Step #5. Clean up the mess

A break in your hot water tank might cause an inexplicable pooling of water towards the water heater tank bottom. However, repairing your hot water system will not suffice; you will have to replace it. Remember to wipe up all the water. Water may be the source of a variety of issues. It has the potential to deform structures, harm personal property, and invite bugs or mold! It’s essential to get rid of it as soon as possible!


It’s A Wrap!

We hope that we have answered you about what to do when hot water heater is leaking. We have discussed a detailed step-by-step guide about it, and by reading it carefully, you can fix this problem at home without hiring a professional. You may also want to read about how to clean water heater and how to install electric water heater in mobile home. Thank you, friends, for staying with us at the end!

Leave a Comment