What does washer dryer hookup mean? It implies a special plug that demands specific wiring and connecting it to the dryer and washer. However, many apartments do not want to have a washer dryer hookup.
If it’s not present around, it means you may not install the dryer and washer but repair the links. Good thing, some of this washer dryer hookup features these connections. Figure out the best way to set the washer and dryer up even with no hookups.
Prepare the needed materials that connect the washer dryer hookup. Please bring the required connections in a washer and dryer to work correctly. Get some tools or items ready that we will be discussing below.
Tools Or Items That You Must Get Ready
Here are the tools or items you need to get ready:
#1. Exhaust vent
An exhaust vent is helpful for a dryer and is suitable for a gas-type of dryers.
#2. Drain
The drainage system is valuable to eliminate water used and get rid of water with no hassles. The drain does this thing.
#3. Hot and cold water supply
A sufficient amount of water is an essential requirement in a thorough laundry. Cold and hot water is the best step to eliminate germs and dirt in clothing. Water is a necessity to rinse off clothes after you wash them thoroughly.
#4. Technical knowledge
The technical knowledge needed is one thing if you have the tools on hand. Set up the washer and a dryer with hookup quickly with technical expertise. Plumbing knowledge is also essential to construct a drain. Carpentry skills are necessary to help mount and set up these electrical outlets and attach the dryer and washer.
Steps To Install The Washer Dryer Hookup
You will know what does washer dryer hookup mean if you’re aware how to install the hookup of your washer dryer. Follow the steps below on how to hookup washer and dryer:
Step #1. Installing the electrical outlet
Install a one-hundred twenty-volt electrical outlet next to the washer and dryer. Verify first if there’s fault protection in the ground for the outlet. Check if the installed breaker carries specifications that you intend to install. Or else, you will change it to a two-hundred forty-volt electrical outlet as this is the suitable capacity in a power supply to control the appliances. Install two-hundred forty-volt type dryers and thirty to fifty-ampere breakers to regulate the devices.
Step #2. Constructing the drainage
The standpipe or drain is suitable for washers and constructed with a two-inch form of ABS pipe. Position the standpipe thirty-four inches on top of the ground, opening higher than overflow level in a washer. Construct it so water will empty in a P-trap and the waste line. Vent the P-trap five feet in the trap and continuously connect it to the existing vent.
You may also want to read about how to install washer drain hose and how to fix a washer that wont drain.
Step #3. Setting up the water supply
Set up the water supply as you get the washer connected to the nearest three-fourths inch main hot and cold lines. Or else, you may attach it closer to the water heater for ease of access to the outlet lines and cold and hot water inlet. Tie the lines with three-fourth inches by one and a half inches tees. They can then run to a wall at the back of a washer. Terminate the water supply lines with the washer’s box and contain a standpipe opening. Know how to install a washing machine & dryer.
Step #4. Installing the vent and dry gas
Install one-half an inch of galvanized iron or block gas dryer. Seek the help of a professional as it can cause a fire outbreak to install the vent as you exit through the side or roof of the house. Next, cut a hole before you seal the gap and install the vet. Afterward, use a twenty-five-foot metal duct pipe that fixes the vent with no further bending. Click on this link to know how to tell if your dryer vent is clogged.
Other Essential Things Involved In Washer Dryer Hookup Installation
Below are more essential things that are involved in washer dryer hookup installation.
- Ensure the dryer vent is free from debris to avoid backup and fire. Install O-ring on the washer hose. Hook up the cold and hot hose to these spouts. Hook up a dryer exhaust to the outlet, plug it in.
- Get these water hoses connected to supply valves and the drain hose and washer to drain connection. Get the exhaust duct and clamp attached to the dryer, including the exhaust connection. Be extra careful not to place some kinks inside the vent.
- Get the hot and cold water hooked up, including drain hoses. Plug it into the wall. Plug the dryer in and hook the exhaust pipe onto the wall outlet.
- Hook up the washer dryer with a screwdriver and large wrench, after you set all these electric outlets. Get the washer attached to water lines, and get it plugged into power. Get the exhaust hose hooked on the dryer and onto the wall.
- Include electrical power and water into a suitable drain.
- Fix the washer dryer hookup onto the wall with some nails firmly, quickly, and conveniently. Call an expert fitter to promise certification and high-quality work.
- Hook the washer and dryer to the power and get the washer attached to water lines.
It’s A Wrap!
Now you have learned what does washer dryer hookup mean that implies a special plug and demands wiring, and connecting it to the dryer and washer. Plus, you know the tools for installing the drain, exhaust vent, hot and cold water supply, and technical knowledge. Just keep in mind the things involved in washer dryer hookup installation!