Wire Tying Strategies: How to Tie Wire to a Swivel

Wire ties are a great way to fasten one thing to another. The type of wire tie you use depends on how much tension you need, how much weight the object is holding and how easily it can be undone. Wire ties come in many sizes and shapes so that they can fit any job.

In this article we will teach you how to tie wire to a swivel using an overhand knot with three loops or an underhand knot with two loops – both tight enough for industrial uses!

How to Tie Wire to a Swivel

Steps on Tying Wire to a Swivel

There are two ways to tie wire to a swivel: an overhand knot with three loops or an underhand knot with two loops. We will demonstrate how to do each of these methods using the first step as our example.

Step One – First you need to take your piece of wire and twist it around until one end is about six inches long. Make sure that the end of your wire is tight against the other end to form a loop!

Step Two – Now take this newly created twist and feed it through one of the loops on the swivel, then back around again until you have twisted three times. Pull both ends so that they are snug and let go. You have now tied one end of the wire to a swivel!

Step Three – To create the other loop, you will need to take your piece of wire and twist it around until one end is about six inches long then feed it through the last remaining loop on the swivel. Then back up again in the same fashion as before, feed it through the last remaining loop on the swivel.

Step Four – Pull both ends so that they are snug and let go. You have now tied one end of the wire to a swivel!

 

What is the best knot to tie on a swivel?

One end of the wire should be twisted around in a knot three times, then fed through the last remaining loop on the swivel. The other end is then pulled tight to create one secure loop at each side of your swivel.

You have now tied one end of the wire to a swivel! Repeat this process for how to tie the wire to a swivel and how to attach it to the other end.

 

How do you attach snell hooks?

To attach a snell hook, tie one end of the wire to your swivel.

Step One – Take three turns around both loops on either side of the eyelet and start feeding it through

Step Two – When you reach halfway down the length, pull tight so that two equal lengths are sticking out from each side

Step Three – Place the wire through one eyelet of your snell hook

Step Four – Tie a knot at how to attach swivels so that they are secure. You have now attached how to tie wire to a swivel and how how to put it on with another piece of fishing gear!

 

How do you attach snell hooks?

To attach a snell hook, tie one end of the wire to your swivel.

Step One – Take three turns around both loops on either side of the eyelet and start feeding it through

Step Two – When you reach halfway down the length, pull tight so that two equal lengths are sticking out from each side

Step Three – Place the wire through one eyelet of your snell hook

Step Four – Tie a knot at how to attach swivels so that they are secure. You have now attached how to tie wire to a swivel and how how to put it on with how to tie snell hooks.

 

How do you attach a snap?

To attach a snap, take your wire and start at the top of one loop, then wrap it around that same loop three times before moving onto the next loop. Continue wrapping the wire around each of your loops until you have how to tie snap hooks finished, then take a quick look at how the snaps should be laid out before using pliers or another tool

Step One – Take your how to put on swivels and line it up with one side how to attach snapper hooks.

Step Two – Take how to tie snap hooks and attach how to put on swivels below the how-to attach snapper hooks. Make sure it is right above where you want your how to put on snapper hook and that they are secure. You have now attached how to layout wire around a spool, as well as how to how snap hooks work.

Step Three – Take how to put on swivels and how to attach snapper hook, as well how to layout wire around a spool, place them in the opposite direction you had how to make a net in earlier steps, so they are facing each other.

Now take you how how to put wire around a spool and how how to attach snapper hooks, place them in the opposite direction you had how to make a net in earlier steps, so they are facing each other.