How To Wash A Car With A Pressure Washer? Here Are The Steps

How to wash a car with a pressure washer? It involves a series of manageable steps like placing the vehicle for a wash, rinsing it with water, applying a cleaning agent, rinsing it off with soap, and drying it thoroughly. You can do this once every two weeks with the use of a cleaning tool, pressure washer. This tool is an effective and faster way to clean a car’s exterior. A pressure washer is easy when you carry it, plus it is more convenient than cleaning using a sponge method and an archaic bucket. There is no doubt that it is safe when used as well. Know how to wash your car correctly with a pressure washer.

 

How to wash a car with a pressure washer

Steps For You To Get Started!

Here are the steps for you to consider to get started.

 

Step #1. Placing the vehicle and time for its wash session

Place the car in the right place before you begin. Do not choose an area with lots of loose pebbles, or it only worsens things up. At times, a burst of water lifts tiny stones from the surface, causing damage to the vehicle’s exterior. Better yet, do the process of cleaning during the morning & afternoon. It is at these times that there is less sunlight. Clean it too during the summer season but place the car under a shade. Or, if you want, choose a place w/shadow. It is not good if you experience immediate drying in the cleaning agents and the water.

 

Step #2. Rinsing it with water

Plug the electric cord into the socket after unwinding the electric cable and water hose. Begin rinsing off the surface with water. Use a twenty-five to a forty-degree nozzle that avoids further damage to its paint. Do this to remove mud and loose dirt from the exterior. Hold its nozzle through its feet and spray from the top up to the bottom. Get near to the tires, although they are grimy. Then, move a bit back while slowing down to spray on view mirrors and lights.

 

Step #3. Applying a cleaning agent

Soap up the surface with a cleaning agent. Use a cleaning agent that is specific to the car surface. Take time to read the manual and fill it with the proper cleaning agent. Get the tank nozzle attached to the spray wand end. Begin underneath as you cover the entire outer surface. Then, get near to the wheels if you think they have stubborn dirt. If you have covered up the exterior already, allow the soap to sit for several minutes. Try to apply it several times if the soap dries out earlier because of the summer heat.

 

Step #4. Rinsing its surface off with soap

Now rinse its surface off with detergent soap. Spray it from the top until the bottom. Direct the stream onto the ground for the soap to flow downward. Then, get the detergent tank disconnected. Keep its wand three to four feet apart from its surface. Spray on those wheels as you remove excess dirt.

 

Step #5. Letting it dry

Dry the car’s surface with a cloth, but one should be of high-quality microfiber. The standard fabric has a rough surface leaving scratches to paint. Lay the fabric flatly on the surface. Pull it slowly, coming toward you. Do the same until you dry every part. Wring out its water as you soak up the cloth thoroughly. Then, begin again. Use a leaf blower if you want a drying process that doesn’t require you to touch. Use it on its high throttle.

 

Safety Precautions To Keep In Mind

  • Avoid further damages by being aware of the safety precautions below.
  • Read the user manual if it is your first time using a pressure washer.
  • Don’t use the device in washing the interior items.
  • Keep their nozzles at a minimum & safe distance, thus avoiding more damage.
  • Decrease the speed of the stream at its fragile exterior components.
  • Never keep its water stream for long and only a single point.
  • Never apply a stream from the bottom up to the top. Or, its dirty water might drain down. Then, you will do the same process again.
  • Focus more on the bottom part of the car. This is neglected, but it’s where the dirtiest happens—the grime and the dirt stick to it. Spend more time in this section. Better yet, get a forty-degree angle in the lance nozzle that makes things easier. This way, you will no longer have to bend it down.
  • Do not use excessive pressure on a car. Beginners usually do this, but please don’t because the pressure washer is powerful. It can break the glass if it is too strong as the pressure should fall around 1200 PSI. This is by far the safest level of pressure that helps avoid cracking the glass.
  • Do not use slippers or sandals when pressure washing. Take note of this as you may spray on your toes accidentally.

 

It’s A Wrap!

Now you know how to wash a car with a pressure washer with the steps mentioned. Include as well the dos and don’ts of cleaning it to be safe at all times. Even if you are a beginner, you can keep these steps in mind to master how to clean it and do not damage the car and the pressure washer, too!

Leave a Comment