Are you wondering about how to vent a dryer through a window? To vent a dryer through your window, open your glass window and install the vent hood there before shutting the window and completely adjusting its side panels. Pull the vent outside and close your window when you’re finished with it, or leave it in place as a sustainable solution.
If you borrow or don’t need to drill a hole in your basement foundation, you may vent a dryer via a window. Instead of drilling a hole through siding, cement, or bricks, you may create a safe semi-permanent or temporary solution using a window.
Yes, my friends, it’s all true about it. So if you’re interested in this topic and want to learn more, continue reading this article at the end. Below we have mentioned all the steps that help you out. Let’s have a deep look at how to vent through a window.
What Is The Purpose Of A Window Vent?
As we all know, a cloth dryer is one of the essential things in your home that help you dry your clothes. Most buildings possess a clothes dryer exhaust installed on the roof or wall, but this sort of ventilation is not always available. In such circumstances, you’ll have to find some alternative for ducting (venting) the heat adequately produced by your dryer. The best way is by using a nearby glass window for venting. Before deciding to vent via a window, there are a few things to think about.
Methods For Venting A Dryer Through A Window
Are you thinking about how to vent a dryer through a window? No doubt venting a dryer via a window is difficult, but you can do it quickly if you know all the methods and step-by-step guides. Below we have written a few simple suggestions that assist you in inventing a dryer through the window. Let’s begin!
Step #1. Get ready to begin
The first step in the venting dryer is to cover your hands and eyes. Wear goggles for eye protection, gloves for the safety of any electric shock, and a dust mask. After that, unplug your cloth dryer from the wall socket and then turn off the main power supply. Start your work after taking all these preventive measures.
Step #2. Remove the window glass
Choose the window that is suitable for venting a dryer. If you have a glass window, remove the window glass first. If your window is divided, you simply need to remove the glass from the section to vent the cloth dryer. You can also take the screen out just after opening the window. Keep the screen in a safe area, such as a garage or closet, so you can change it whenever you want to move.
Step #3. Measure the size of the hole
After measuring it, cut a bit of wood, acrylic, or plexiglass to fit into the window opening. Your insertion must be tight and sufficient to fill the gap.
Step #4. Make a vent mark
Make a mark in the middle of the insertion. Then, either cut a hole for the jigsaw or just use a hole cutter to create a gap around 4-inch.
Step #5. Put the dryer in place
The dryer vent hood should be inserted into the hole, facing the entrance downward. This will also be a tight fit. Seal the flat piece’s region on the vent’s hood to the insert with a caulking gun and caulk.
Step #6. Put the plexiglass in place
Inside the window, put the insert in. Use window locks and or board in the track or a cut-down broomstick to fasten the window so it can’t be opened externally if you just opened it to allow access.
Step #7. Caulk the insertion
Apply caulk to the insert’s edge, at which it joins the window screen with the caulking gun. The elbow may be installed while the window insert and vented hood are in place.
Step #8. Add the vent elbow
On the interior of the dryer vent hood, install a 4-inch pipe elbow. Place it facing the dryer, where you’ll connect the long 4-inch-diameter dryer pipe to the exhaust vent at the base of the dryer. Secure the elbow to the vent hood using foil tape.
Step #9. Add the vent pipe
To the elbow, connect the metal pipe or the flexible duct. To establish a secure connection, use foil tape. You may have to install an elbow towards the dryer’s output vent to join the vent pipe. Attach the line to the elbow and cover it with foil tape after adding the elbow. Know the ways to clear a clogged waste pipe
Step #10. Check for air leaks
The last step is to check for leaks while the dryer is running. There should be no leakage if you read the directions carefully. Run your hand around the pipe while the dryer is on to see whether you leak. If air is seeping out of the taped joints, plug the leak with extra foil tape.
It’s A Wrap
We hoped that you all would understand how to vent a dryer through a window from this article. Above, we have mentioned all the steps that help you out. After reading all these steps carefully, you all will vent a dryer by yourself. Thank you, friends, for being with us at the end! You may want to read related articles; know how often to clean a dryer vent and how to tell if your dryer vent is clogged.