How to use Troy Bilt pressure washer? Follow the steps to remove the oil cap in an engine crankcase, pour oil into it, place the cap back and tighten it. Remove the cap in the fuel tank and fill it with gasoline. Place the pressure washer next to a water source outside to supply water. Then, inspect the hose connected to a pump and a spray gun. Position the unit at a certain level. Attach the hose to the water inlet of the pump.
Troy-Bilt, an equipment company, based in America, has manufactured garden and lawn machinery. They are well-recognized among lawn mowers and tillers. They are so far the biggest producer of pressure washer series.
Most of these pressure washers are run by gasoline engines, with fuel tanks ranging from one-fourth to one-third gallon capacity. Using this pressure washer is simple as the first thing to do is fill the machine with fluid. Read on further to learn more information about it.
Steps To Use Troy Bilt Pressure Washer
Connect first the water supply and turn it on before you operate the pump. If there’s no water, it might only damage the equipment. This damage may cancel the warranty in a pressure washer. Well, anyway, here are the steps on how to use Troy Bilt pressure washer:
Step #1. Turning the source of water on
Turn the water source on and direct the spray gun safely in its direction. Press the trigger to remove the air in the pump system, including its impurities. Place the device next to an area where you will work. Place the pressure washer on a flat surface.
I guess it’s helpful to read about how much water does a pressure washer use.
Step #2. Connecting the extension
Get the nozzle type of extension connected to a spray gun. Tighten it safely using your hand.
Step #3. Engaging the trigger lock
Get a trigger lock engaged in a spray gun trigger so the latter will keep on moving; position the trigger lock directly after the trigger. Connect this in the handle’s interior. The lock is a safety feature that prevents spraying water while starting the engine.
Step #4. Moving the throttle lever in a “fast position”
Position the throttle lever in a short position. Click to discharge a primer bulb in an engine 6 to 10 times injecting fuel in the fuel line.
Step #5. Moving the choke lever in a “choke” position
Position the choke lever in a “choke” position. Position the choke lever in “run” to warm the engine more.
Step #6. Positioning yourself
Start the engine as you position the machine. Take hold of the handle of the starter. Pull it slowly until finally, until you feel resistance already. Pull it fast to begin the engine and pull its starter rope ten times until the engine starts. If it doesn’t begin despite several attempts, wait for several minutes and start again. There could be flooding in the machine.
Safety Precautions To Avoid These Incidents
Rapid retraction of starter cord kickback only causes bodily harm. Remember that kickback occurs if the cord pulls the arm and hand toward the engine quicker than what you would let go— injuries like fractures, broken bones, sprains, and bruises can kickback. So, follow the safety precautions below in avoiding these incidents.
- Wear your goggles.
- Relieve the pressure in a spray gun first before pulling its starter cord.
- Pull the cord slowly until you feel its resistance as you start the engine. Pull it rapidly again, avoiding kickback.
- If the power still fails and it doesn’t run, direct the spray gun towards a safer direction. Press the trigger in a spray gun to release high pressure. Engage the lock in a spray gun trigger.
- Clench the spray gun firmly with your hands if the device is its high-pressure type of spray. Avoid injury as you follow this as a spray gun kicks itself back.
Reason Why The Troy-Bilt Pressure Washer Doesn’t Start
If the Troy-Bilt pressure washer doesn’t start, it could be since it’s sitting idle already. If you’ve used it out after several days, the fuel from last day’s use is stale. It’s the leading cause of the damage to the machine.
Easy Checks To Follow To Use Troy-Bilt Pressure Washer
Perform these easy checks to ensure no problem arises in the fuel line.
- Check if you’ve already switched the device, to begin.
- Check if no wires are cut or have come loose while the pressure washer sits in the storage.
- Check if there is fuel left inside the tank. If it has none, fill it up.
- Check if there is no oil in the engine crankcase.
- Check if the air filters, oil filters, and spark plugs are placed correctly.
- Grab some spark plug tester to see if there’s a spark in a plug upon pulling a starter rope.
Well, anyway, you can try these 9 ways to use a pressure washer that will blow your mind.
It’s A Wrap!
Now you learn how to use Troy Bilt pressure washer as you follow the steps to remove the oil cap in an engine crankcase, pour oil into it, place the cap back and tighten it. Remove the cap in the fuel tank and fill it with gasoline. Place the pressure washer next to a water source outside to supply water. Then, inspect the hose connected to a pump and a spray gun. Position the unit at a certain level. Attach the hose to the water inlet of the pump. Plus, keep the information in mind as you perform easy checks and safety precautions!
You may also be interested to know about how to use a Honda pressure washer and how to use Greenworks pressure washer.