How To Use Soap With A Pressure Washer? 6 Easy Steps!

Are you wondering how to use soap with a pressure washer? Locate the bucket or detergent tank first, use a brush or detergent spray, choose the suitable nozzle, spray soap upwardly, avoid streaks, allow the soap to stay for 10 to 15 minutes, and rinse the surface off using a high-pressure nozzle.

Remember that pressure washing is an effective way to remove stubborn stains in the entire house. Using soap or detergent using a pressure washer helps enhance its cleaning results.

How to use soap with a pressure washer

Moreover, soap with pressure cleaning helps clean grease and dirt from the driveways, decks, sidewalks, exterior surfaces, and siding. Let’s begin to read this article!

 

Steps When Using Soap With A Pressure Washer

Below are steps to consider how to use soap with a pressure washer.

 

Step #1. Locating the bucket or detergent tank

Locate first the detergent tank and let soap fill it continuously. If there’s no detergent tank, it’s ok to use a container or bucket for the soap hose. Put some soap into the detergent tank as you turn the valve on, starting the pressure washing cleaning. Then, connect the input of the cleaning solution to the pump and place the other hose end into a diluted solution in a bucket.

 

Step #2. Using brush or detergent spray

Put the cleaning solution to the brush to achieve thorough cleaning, alongside a pressure washer brush. Attach the side of the cleaning spray in the pressure washer to a cleansing solution bottle; it works the same as a detergent tank, use this bottle to replace a detergent tank.

 

Step #3. Selecting the suitable nozzle

Attach the high-pressure washer nozzle and rinse the mess away with detergent or soap, with nozzle selection as an essential component of pressure washing. The suitable nozzle helps you remove dirt from the surface more efficiently, faster, and better. Also, utilize a soap nozzle, so it’s compatible with a pressure washer plus, it’s reasonable in flow rate. Apply a detergent but use some low-pressure nozzle, or else washing in high pressure is excellent. The step helps pressure washer detergent chemicals from combating the stains they want to remove.

 

Step #4. Spraying the soap upwardly to avoid streaks

Spray water onto the surface that thus, loosens grime and dirt but before that, dry the surface first and adjust the temperature past 50 degrees Fahrenheit. Spray it upward when your pressure washer is using soap to avoid streaking, as this helps make the process easier while also making it easier on your part. Spray it upwardly, preventing streaks and ensuring soap distributes evenly on the object’s surface. Moreover, it helps avoid runoff and overspray due to downward spray or no soap spray. Nonetheless, keep the nozzle hose at length away from your arm and the object’s surface to not damage the device.

 

Step #5. Letting the soap sit for ten to fifteen minutes

Allow the soap to break down grime and dirt on a surface that when you pressure washes with soap; wait for ten to fifteen minutes before it does the job entirely, as this helps offer a better clean while removing dirt not removed by soap. Pressure wash but not wait for the soap to break down, or it might cause a more enormous mess when cleaning it up afterward.

 

Step #6. Rinsing off the surface using nozzle in high pressure

Use a nozzle set in low to high pressure, which is the last step to consider. Wash all the grime and detergent away using water at high pressure. Next, try to use the device with hot water to achieve profound cleaning results, and as you heat the water, you also accelerate the cleaning procedure. Moreover, use a leaf blower or squeegee that dries off the surface before you apply any paint protection or sealant to it. You may also be interested to know about pressure washer troubleshooting.

 

Safety Of Using Soap In A Pressure Washer

Safety is also as promised by using soap in a pressure washer, as this serves as a usual practice. So far, it’s the best way to clean a surface, plus it’s the safest. It helps remove grease and dirt from the covers with no damage to them, which also reduces leaving the surface looking shiny and clean and scrubbing. Soap has lower chances of damaging surfaces, especially if not extremely dirty, as this means that you can use it on new surfaces with no further issues. Even on concrete surfaces, it’s safe to use soap in a pressure washer to clean grease or dirt. But then, be extra cautious since soap could only leave nozzles clogged and cause the device not to spray anymore.

 

Best Choice Of Soap To Consider Using

Remove oily substances and remove dirt from surface pores with soap to avoid slippery residues as they form on the surfaces after cleaning. There are many soaps to buy on the valuable market for pressure washing. But then, alkaline soap seemed helpful when cleaning a driveway or deck, while acid soap is beneficial when cleaning stone or brick surfaces.

 

It’s A Wrap!

Now you learn how to use soap with a pressure washer as with the steps discussed above. Be extra careful with following each of them to remove dirt from surfaces successfully. But more than that, including the use of soap to remove dirt or grease effectively. Don’t worry, since safety is as promised by using soap with a pressure washer! You may also want to read about how many gallons per minute does a pressure washer use and what does cold water pressure washer mean.

Leave a Comment