How to unhook washer is simple as long as you follow some easy steps: turning off the water valves, dragging or pulling the washer, unplugging the washer, getting a bucket, and unhooking the hoses from the washer. Helpers should also be nearby if there are stairs for you to maneuver.
Move the washer when you replace or transfer it to a new house. Disconnect it from the wires and hoses, supplying water and power. Follow the instructions below to guide you through the process of unhooking the washer and moving it to the following location. There is so much more to learn about this topic, so without further ado, let’s start!
Steps To Unhook Washer
So, how to unhook washer? Here are the steps to keep in mind and follow when unhooking the washer.
Step #1. Disconnect the washer
Get the water valves turned off while they usually supply cold and hot water right behind the washer. Turn these valves clockwise until there is no turning any further. Do so to protect you from spills if you tear a hose.
Step #2. Drag or pull the washer
Grab the side of the washer and push it forward if you are working alone. Do the same thing with another side. Try to pull on the opposite sides if there is someone to help. Pull the washer as far as you want without stressing the hoses. It should be at a distance from the wall.
Step #3. Unplug the washer
Be sure the washer does not run as you decide to unplug it. Plugging the washer from the outlet will disconnect it from the power supply.
Step #4. Grab a bucket
Place a bucket or water pan near the washer right below the water lines that catch water. Then, surround it with towels that will catch the water or leaks that spill out from detached pipes.
Step #5. Disconnect the hoses
Hoses attached to clamps require you to turn the screws above the clamps. Follow the counterclockwise direction until you loosen up the clamps already. Point the hose’ ends to the bucket and drain the water. Place the hoses right through the drain of the washer box. Check the valves several times if they are off before you do this. Faucet handles in styles are easy when you turn it back on or move the machine or step behind it. Then, wait for seconds after you turn off the valves and remove the hoses. Pressure in the hose declines, thus; it’s easy for you to remove it. Turn on other faucets inside your house to drain them more quickly.
Step #6. Take the hoses away from the wall
Turn the hoses’ ends in a counterclockwise direction until finally, the hoses detach. Adjustable pliers or pipe wrenches help loosen the hoses, particularly if the washer disconnects for some time. After you remove them, drain the rest of the water into the bucket.
Step #7. Take the drain hose away from the drain
Doing so depends upon the plumbing setup as the drain may be a tall and stand-pipe, wall-mounted type of drain, floor drain, and laundry sink. They each require a different process in removing a hose. Follow the instructions with the washer if it is not yet obvious. Now, point the end of the house to the bucket for the water to flow out. My friends, it may be helpful to check about how to install washer drain hose.
Step #8. Prepare the washer to move out
Get the water bucket emptied before you move the washer out. Wipe for any drips or spills.
Step #9. Double-check the connections
No extra hoses or plugs should connect the washer to the wall. Move the washer out as water is there inside.
Step #10. Clean the water intakes
Remove the water intakes if you keep them in the washer. Use a bristle brush that will eliminate debris that accumulates for years. Read how to clean washer drain hoses.
Step #11. Take the power cord away
Take the power cord away unless you set the washer back up in a similar spot. Tape it instead if you cannot remove it as this safeguards the plug and avoid the cord as it pulls out from moving. Remove possible knobs arising from the washer that will also prevent loss.
Step #12. Secure the washer’s inner chamber
The inner chamber of the washer is also known as the drum. Now, secure it first if you will move the washer at a significant distance. Do this with the use of special bolts but know that it depends on the model of the machine. The special bolts are large and y-shaped foam pieces. Read the manual in securing the machine drum, and buying a special kit is also needed in this case. Also, know how to fix a washer that wont drain.
Step #13. Wrap up the parts
Leave the cords fixed to the machine if you will move them at any distance. Tape the dangling lines to the washer or the sides to avoid them as you go on your way.
It’s A Wrap!
Now you learn how to unhook washer with the steps mentioned. For as long as you follow them clearly, it will be accessible on your part. Get some help, too, if you need it. Prepare all the tools required to make the process more convenient! Thus, you can use the washer again! You can also read about how to open a washing machine’s casing.