Are you wondering about how to turn on water heater? Don’t worry; you have arrived at the right place. A water heater with electric functions involves turning on the circuit breaker, making sure your water heater is complete with water before turning it on is among the most crucial measures. After this, you need to check the open valve and faucets and turn them off.
If you were using a gas water heater, you need to light the pilot with a low or high heat option; you need to hold the pilot button for 15 to 20 seconds to make it operational.
But if it does not start at this time, you should press the spark generator for 5 seconds after you set the heater pilot opens the cold water to add in, and it will start heating the water. Continue to reading to learn more!
Steps To Turn On The Water Heater
The water heaters are of many kinds like the electric water heater, gas water heater, and tankless water heaters. If you are new to the water heater and feeling confused about how to turn on water heater, you need to read all the below-mentioned steps to turn your water heater on.
Step #1. Close the open valves and faucets
Inspect your electrical water heater’s uncontrolled vents or valves. If you find any faucets valve opens, turn them off to avoid any mishappening. Anyone you come across with an open door should be closed right away. The same thing you need to do if your heater is of gas, the very first thing you should do before turning on the water heater is to shut any opening valves. When turning on the electricity, double-check that the tank is full of water. You don’t want the heater to warm a practically empty tank. This might lead to the failure of your water tank and the heater.
Step #2. Turn on the heater switch
The switch for your heater is suitable and safe to be switched on right now. The heater should start heating the stream at this time. Certain electric heater types might not indicate when the appliance is turned on. Low sounds, on the other hand, would signal that now the water heater is working. If you are using a gas heater and want your warm shower back on track, you should relight the pilot light on your heater. This is indeed necessary to prevent any gas-related incidents.
Step #3. Turn on the gas valve
Users won’t go through the piloting light stage if the faucet is set to “pilot.” All you’d have to do is switch on the gas valve. However, your heater may already be warming the water, and you must turn on the flame during this stage. If that’s not the situation with the heater, users may need to return to the pilot lighting step.
Remember These Safety Guidelines While Turning Your Water Heater On
Inspect your outflow pipe for leaks. The temperature is too high; you need to reduce it quickly. While using a gas water heater that isn’t used in quite a while, keep an eye out for other leaking gas smells. Gasoline smells awful for just a cause, so if you don’t understand what it smells like, some persons equate it to the stench of the strong smell when you ignite the pilot.
You don’t need to restart if there is a scent like fuel, gas, paraffin, or any other propane canister. If you’re a relatively recent heater, then may not be able to light it. If you have to switch on the heater because the pilot light has gone out, look into the problem. If you’ve not fixed the problem, don’t try to switch the heat again on.
Test to see if the heater can be relit and whether the vent is operational. Look for naked wires or debris if you’re using an electric heater. When there is, need not restart your heater till you have thoroughly rectified the problem. If the heater keeps going off and no, despite how often fuses, users change, or how many times you set the circuit, you must change it. Determine the distance first from the aperture while igniting a pilot light or switching on the gas valve. Your entire body, particularly your eyes, must be kept safe. You might be seriously burnt when you’re not attentive, and delay igniting happens due to a filthy burner or possibly the out pilot.
After lighting the pilot, inspect your heater for dirt, corrosion, or filth. Should not fire the flame if it is coated in soot, corrosion, or filth. Before igniting, you’ll need to cleanse the burners or have them cleaned. Before you switch just on the gas valve, the outer and interior covers are securely fastened twice that amount.
Click on this link to know when to replace water heater.
It’s A Wrap!
We hope that this article helps you learn about how to turn on water heater. However, if you feel you are not well aware of the water heater turning on the process, read this article until the end, and must-read follows the safety guidelines mentioned above to avoid misleading information. Thank you, friends, for staying with us! You may want to find out how to turn off water heater and some water heater checklist.