Are you wondering about how to troubleshoot an electric water heater? Here are a few steps that help you fix the water heater problem; you can learn them as you further delve into this article.
Electric water heaters provide dependable and efficient hot water for your house or company. When problems develop, you’ll like to diagnose the problem and implement the appropriate solution rapidly.
It’s critical to keep safety first while troubleshooting water heater problems. Before looking at an electric hot water system, turn off the electricity at the wall outlet. Here are some of the most frequent electrical water heater issues and how to solve them. There is so much more to learn, so it’s best to dig into this article further!
Ways To Troubleshoot An Electric Water Heater
Because of extensive water heater use, sometimes it doesn’t work effectively. It doesn’t produce enough hot water, or the water is rusted or smelly. To get rid of these issues, you must know how to troubleshoot an electric water heater. So, let’s get started!
#1. Examine the guarantee
For both industrial and residential water heaters, minimal guarantees are provided. Every device has a rating plate that includes the serial and model number. All such figures will determine if the tanks would be insured by a lifetime guarantee, including a replacement unit or components for nothing or at a discounted cost. This is something you may perform before you start identifying the problems.
#2. Lack of warm water
It is also conceivable that a hot water tank that is not producing hot water isn’t receiving power. It has a tripped limit switch or one or more malfunctioning heating components. First, check whether the water heater’s circuit breaker has blown at the main switchboard. Switch the breaker off and on once more if it has triggered. If your heater’s breaker hasn’t tripped (and it’s running), attempt adjusting the heater’s high-temperature limit; here’s how to fix the problem:
Switch down the circuit breaker again for the hot water system in the service panel. There is an access panel in the water heater; remove it for its higher heat source. Carefully pull the safety barrier and the insulation, being careful not to come into contact with any electrical connections or wires. Click the red high-temperature cutoff reset button located just over the top thermostat. All insulation, the access panel, and the safety guard must be reinstalled. Set the heater’s circuit breaker to on. If any heating elements aren’t working, replace them as needed.
#3. Hot water is inadequate
Your water heater may be too tiny to fulfill your family’s hot water requirements if it produces hot water but not much of it. Check to see whether the demand exceeds the water heater’s capacity. Below, we have discussed how to troubleshoot this issue:
75 % of the capacity of the hot water system should be used to heat water. For example, a 30-gallon demand requires a 40-gallon water heater. Have quicker showerheads, utilize the low-flow showers, and undertake household activities at different times of the day instead of simultaneously if the demand for heated water is beyond the heater’s capacity. If the system isn’t tiny but produces less hot water than it used to, one or both of the heating components may have broken.
A defective top heat source across a whole shower implies a continuous warm water supply. A defective bottom heating element suggests warm water flowing quickly throughout a showerhead. It may be helpful to read about how to adjust temperature on hot water heater.
#4. Bad odor
The most prevalent issue related to your water heater is rusted water. If your water has a red, yellow, or brown hue as it flows out of the tap, corrosion may be present within your hot water system tank or in your home’s pipes. There might be microorganisms in the water heater tanks if your water smells like rotten eggs. You may have to repair the anode rod inside the tank, which usually necessitates the assistance of skilled plumbers. Also, you need good service and maintenance of your water heater for troubleshooting this issue. It’s a great idea to clean the water tank once a year to get rid of foul odors.
#5. Noises from the tank
Is your water heater making strange noises? Do you hear a deep rumbling or popping sound? Is it a high-pitched scream, perhaps? The sounds you’re experiencing may be the noise of boiling water. High sediment building in the tank’s base might lead the floor to heat up, resulting in the water boiling. Anyways, for troubleshooting this issue, you may have to do this step: To get rid of the sediment in your hot water tank, the first attempt is to empty the tank. If it doesn’t work, the tank may have to be replaced. You may also want to read about how to replace a water heater element.
It’s A Wrap!
After reading this article, we hope you will better understand how to troubleshoot an electric water heater. Above, we have discussed how to fix your water heater issue by using them. Anyways, before troubleshooting, don’t forget to check your water heater warranty. Thank you, friends, for touch with us; don’t forget to share this article with your friends if you like it! Read more about water heater troubleshooting.