In this how-to article, we will be discussing how to take apart Ikea Patrik Swivel Chair. This is a straightforward process that should not take up too much of your time. We will also include some helpful tips on how to put it back together again!
Steps on Taking Apart IKEA Patrik Swivel Chair
Step 1. Set up the chair how you want it to look before taking it apart. This will help when putting back together again and make sure everything is in order.
Step 2. Remove all screws from the seat frame (except for two screws on either side of the swivel). In other words, remove one screw on each end across from where the seat and back meet.
Step 3. Now, remove the screws from the front legs of the chair (again except for two on either side that is across from one another). These should be easy to spot as they have a different size than other screws.
Step 4. Lastly, unscrew any remaining visible bolts to take off each leg of the frame individually; this will help you access all parts easier without having anything get stuck or tangled up by accident.
Steps on Putting Together IKEA Patrik Swivel Chair
Step 1. Set up how it was before taking it apart first so your original measurements stay intact and everything lines up correctly. Place feet into the base then screw them in place with screws provided/recessed into the foot.
Step 2. Attach the seat onto a chair to form a “Z” shape. This will also allow for it to rotate 360 degrees when in use if desired.
Place back on, lining up with how you previously took it off and screw into place using screws provided/recessed into frame of base.
Make sure everything is aligned before fully tightening down all bolts or else they may come undone again by accident and cause more work than necessary.
Use pliers if needed as well so everything stays lined up correctly while attaching; this can be done after each step until the final bolt is tightened at bottom of the chair leg (this should not need any tools).
How do you Remove the Base From an Ikea Chair?
Step 1. Start by removing the seat from its base and then use a hard surface to push all four legs in at once. This should cause them to fall out of their joints, which will make it easy for you to take apart further.
Step 2. Remove any leg caps that are still on with your fingers or pliers before taking off the other three legs (or how many remain attached). Then, remove screws and bolts using a Phillips head screwdriver if necessary.
If there is more than one type of bolt holding something together, try removing those first as they can often be difficult to undo especially when partially covered by another piece of hardware.
Step 3. Once these pieces have been taken off, remove every last bolt/screw so that you can finally remove the chair from its frame.
How do you Disassemble a Hydraulic Chair?
Step 1. First, remove the hydraulic cylinder from where it is mounted on the chair.
Step 2. Next, use two wrenches to disconnect the upper and lower brackets that are holding one of those rods in place. Remove this rod by hand or with a puller while keeping an eye out for how tight bolts need to be replaced before putting them back into their original position (don’t worry about these too much just yet).
Step 3. The next step would be removing all fasteners using both a hex key wrench and pliers. Then, take off any remaining mounting hardware such as screws/bolts without forgetting how they were originally oriented when you put them back together last time – don’t forget how tightly each bolt should have been tightened!
Steps to Remove Bolts Using a Phillips Head Screwdriver:
Step 1. If there is more than one type of bolt holding something together, try removing those first as they can often be difficult to undo especially when partially covered by another piece of hardware.
Once these pieces have been taken off, remove every last bolt/screw so that you can finally remove the chair from its frame.
The hydraulic cylinder will need some kind of lubricant and then be reassembled in reverse order. It’s important not to lose any parts while disassembling this part because it could take weeks for the new part to arrive.
Additional Information:
The hydraulic cylinder can be a little tricky and needs extra care when being taken apart. It might help to put the bolts in order before removing them so that they don’t get mixed up or lost.
To reassemble, it is important not to lose any of the parts as this can take weeks for replacements to come in from Ikea if you do–sometimes they don’t have these specific pieces at all!
Steps on how to remove bolts using a Phillips head screwdriver
Step 1. If there is more than one type of bolt holding something together, try removing those first as they often prove difficult especially when partially covered by another piece of hardware.
Step 2. Carefully remove the bolts with a screwdriver or wrench. It can be difficult if they’re tightened down and may need to use two tools at once, one in each hand.
Step 3. If there are unfinished holes left behind, you might want to put some screws into them before putting the next piece back on for stability’s sake.