How to set Bassinet Up? A DIY Guide

A bassinet is designed for newborns up to six months old. We know how important it is for you to have your baby in the room with you, which is why we created this model with a rocking motion that gently rocks them back and forth.

The soft fabric makes it easy for them to sleep soundly without waking themselves up at night. This guide will show How to set bassinet Up in minutes!

Model 5610-N Bassinet

What is a Bassinet?

A Bassinet is designed for newborns up to six months old. We know how important it is for you to have your baby in the room with you, which is why we created this model with a rocking motion that gently rocks them back and forth.

The soft fabric makes it easy for them to sleep soundly without waking themselves up at night. This guide will show how to put this wonderful bassinet together in minutes!

 

Steps on How to Put Bassinet Together

Step One: Place the mattress on top of the base frame by lining up the holes where each screw goes using an Allen wrench (included). In order from left to right, insert screws into their corresponding holes until they are firmly set into place but do not tighten too much.

Step Two: Push the mattress down into the frame firmly and make sure it is in place before continuing to tighten each screw by twisting them counterclockwise until they are tight (do not over-tighten). Make sure you do not twist too much or else this can cause damage to your product!

Step Three: Insert the four legs into their corresponding holes located on each corner of the frame, and make sure they are firmly set before tightening them by screwing clockwise.

Step Four: Place your new bassinet cover over the top of your mattress with the opening facing down towards a changing table or dresser (if you do not have one available). Fold up both bottom corners to align perfectly in line with either side so that when placed onto your product it looks symmetrical.

Step Five: Place the mattress on top of your bassinet with the opening facing down. Match up all four corners to make sure that they are aligned correctly and not crooked or twisted, then push firmly into position so that it is straightened out perfectly before inserting any zippers or buttons.

Step Six: Once you have inserted all three zippers evenly across from each other on both sides, attach one end of a bungee cord onto the back-centre loop located at the middle bottom side (in line with how you would fold up your product) while keeping opposite ends even in length, pull tightly until secure but without causing too much tension for how hard this part can be!

Step Seven: Repeat step six by attaching the remaining bungee cord to opposite ends on the same loop.

Step Eight: With both cords pulled along your entire bassinet’s perimeter, try folding up the product making sure all three zips are even and line up perfectly with each other before fastening end clips together!

 

How to Loosen the Straps on a Baby Trend car Seat for Easier Installation Into the Car

Step 1. Lift latch plate. Pull down the strap until tight. Push buckle through the slot of the lower anchor connector.

Step 2. Connect upper clip onto vehicle’s tether hook located above the rear window, if equipped with one. If not then connect it to any standard metal D ring or doorknob/handle within reach from the child restraint location where installed.

Step 3. Pull the loose end of strap out of storage compartment on backside bottom section of infant carrier base (strap should slide freely out). Repeat steps for the opposite side.

To install click the front button located at the chest near the handlebar which locks in place. Lay infant carrier base on the ground with storage tray facing upward.

Step 4. Locate buckle tongue and pull the strap over both sides of the chest clip making sure it is routed through all loops properly. Pull the strap tight enough to hold chest clip closed but loose enough so that when the release button under its top flap is pressed, it opens easily without dislocating any part of the seat (the strap should be able to slide freely).

Step 5. Push belt back into compartment if not already there from the previous step in how to install a model 5660 e bassinet instructions below. Repeat steps for the opposite side.

To ensure proper installation check upper anchor connectors are securely attached by pulling your body weight away from the vehicle’s tether hook or handle/knob (see how to install a model 5660 e bassinet instructions below).

Step 6. Check that the four corners of your vehicle’s safety belt are routed through the upper anchor connector loops (two in front and two behind) correctly.

If they have not already been done, pull the strap tight enough to hold the chest clip closed but loose enough so that when its release button under its top flap is pressed, it opens easily without dislocating any part of the seat.

 

Steps on How to Use the Sit & Stand Strollers

If your baby falls asleep in the car, there is no need for them to wake back up again once they are home. You can get into the house without waking them up by using one of our great ride along walkers. Once inside, strap your child safely into their crib with these instructions.

We know how important it is for you to have your baby nearby at all times and we hope that this guide helps make life easier! The Model 5740 S has been designed as a perfect sit and stands stroller, making it easy for you to use.

The wheels on the Model 5740 S move easily, allowing your child to continue standing up while not in motion and giving them stability when they are moving around.

Leave a Comment