A big recliner is a great place to relax in the evening. But what happens when it breaks? You can’t just get rid of it and buy another one unless you want to spend hundreds of dollars.
So how do you fix your chair? In this article, we will talk about 7 DIY ways that you can use to replace lazy boy recliner seat springs so that they are as good as new!
Steps on Replacing Lazy Boy Recliner Seat Springs
Step One: Materials Needed and Tools Required
The first thing you will need is the right materials. You can use a screwdriver, pliers, wire cutters or some scissors to get started with your project. As for tools required for this job they are very minimal as well, but you may want to have needle nose pliers and a screwdriver handy.
Step Two: Remove the Old Springs
Before you can put new springs on your chair, you will need to remove any old ones that are still installed in it. To do this all you have to do is unscrew them from where they were screwed into the frame. You may want to use the pliers to grip the fastener and unscrew it at an angle so that you can get a good hold of it.
Step Three: Install New Springs
Now that your old springs are removed, all you have to do is screw in new ones! This should be easy since they will come with instructions for how far apart to place them in the frame. The only thing to be careful of is not cross-threading or damaging your new springs, so make sure you use a screwdriver that will fit nicely into the grooves and screws without being too big for it.
Step Four: Mount Seat Cover on Top
Now all that’s left to do is put your seat cover on top of the springs and reattach to your frame!
Step Five: Test Seat Recline
Once you’ve done that, just test out how far down your new springs will allow you to recline. You want it to be able to go all the way back without any resistance or stop unless you need a footrest.
Step Six: Replace the Screws and Put Everything Back Together
Now all that’s left to do is replace your screws, put everything back together, and you’re done! If anything doesn’t feel right or there are any gaps just tighten up a screw here or there until it does.
The only thing left for you to do now is to sit back, relax and enjoy your new springs!
How do you Replace a Tension Spring on a Recliner?
Step One: Unscrew the Springs
First, you’ll need to remove your springs from under the fabric on top of them. If they’re sewn in, carefully cut around them with a sharp utility knife and then pull out any remaining stitches or threads holding them down.
If there’s room between your seat cushion and backrest, you can just unscrew the springs from below.
Step Two: Purchase a Replacement Spring
Next, purchase and replace your tension spring with one of equivalent strength. Just remember that if it’s too short or long for your chair then it won’t work correctly!
Step Three: Sew Them Back In Place. Lastly, sew your new tension spring in place and enjoy your new springs!
How do you Measure a Spring for a Recliner?
The easiest way to measure a spring for your recliner is by how long it should be. You want the coil of wire, which has been coiled up and cut down lengthwise, to have enough slack in its coils so that when you let go of one end, it will stretch out about two feet before stopping.
Tools needed for spring replacement:
- Phillips screwdriver
- Pliers or vice grips (optional)
- Metal file if you have a metal frame on your recliner chair seat springs
- New screws to replace the old ones with, which will be included in most kits. You can also reuse some of the old ones if they are in good shape.
A basic understanding of how springs work and a bit about your specific chair’s design
Why do Recliners Lean to one Side?
A recliner’s leaning to one side is most often due to a broken spring. When the two coils of wire that make up each spring are no longer stretching evenly, this creates an odd weight distribution and will cause your chair to lean in favor of the coil with less tension.
How to Protect a Recliner to Last Longer
If you own a recliner, it’s important to take care of your chair and keep up with the maintenance that goes into keeping one in good working order. The most common thing people do is adjust their springs every six months after they’ve been sitting in the same spot for about four years. This stops them from weakening over time and helps to make sure the chair is safe to use.
How do you Replace a Recliner Slipcover?
A recliner slipcover is one of the easiest ways to revive a tired chair and give it new life. If you have an old, worn-out recliner at home that desperately needs some attention, but don’t want to spend money on buying a whole new set or even just replacing the seat cover, then this DIY project will be right up your alley.