How to remove drip tray from fridge? Do you sense water flowing from the back of your refrigerator, and you think there’s a problem with the drainage? Then, that might be the drip tray of your fridge. Even though you cannot remove some trays, we’ll still walk you through the six steps you’ll need to do to remove or clean them. And if there are any defects, you need to replace the tray, so these steps are necessary.
Appliances such as air conditioners and refrigerators produce condensation inside its unit due to the temperature changes. And all of them have drip trays to catch the condensation and prevent the water from flowing outside the fridge. So, this component mustn’t have any dents or cracks to hold the water effectively.
Also, the first thing you check when there’s a problem with the drainage is the pan or the drain lines.
And if you don’t know what’s the first thing you should do, this article will help you out. So, read on!
Steps How To Remove Drip Tray
How to remove drip tray from fridge? Most fridge components such as the compressor and drip tray are at the bottom back part of your fridge. Hearing about these parts may sound complicated, but this process will only take a couple of minutes. Also, with the help of this guide, you don’t have to call in a professional and spend money on a procedure that we believe you can do. So, the following are the steps we gathered on how to remove drip tray from fridge, and we’re going to explain them to you clearly.
Step #1. Gather your tools
If you only want to check if there’s a problem with the tray or you want to replace it, you need some gloves and a screwdriver. This tool will help you open the cover on the back of the fridge. However, if your goal is to drain the water and clean the tray, you should prepare some bleach and cloth.
Step #2. Read your manual
Before we make any movements to your fridge, we must first locate where the tray is. We mentioned earlier that it’s usually on the rear side, but some trays are located in the front depending on the fridge’s design. Also, your manual might have some instructions to access the tray, and it might help.
Step #3. Turn off fridge and water supply
Perform this step to prevent electric shocks and any complications. So, press the power button in the control board and unplug the cable. With this, we can move the fridge forward if the tray is located in the back and have enough access. Also, you don’t have to disconnect the waterline, but you can switch off the valve.
Step #4. Prepare the fridge
If the tray is in the back, move the fridge forward as much as you want until you have enough access to the bottom panel. Then, use your screwdriver to unfasten the cover of the internal components of the fridge. After popping it out, you have the vision of the parts, including your drip tray. However, if it’s in the front, you don’t have to move it forward. Instead, locate the grill cover on the bottom front of your fridge. To remove the kick panel of your unit, use a putty knife or scraper.
Before taking it out, be careful not to damage it and make sure all sides have popped out.
Step #5. Remove the tray
You can locate the tray quickly because it’s the component that holds water. Taking it out is simple, and you have to wiggle it first to loosen all sides. Then, pull it up while maintaining its position to avoid spilling the water and pull it towards you.
In some cases, you could not remove the tray, especially when the heating coils in above it. You can examine the diagram in the manual to check if the heating pipes are in a similar location. Please don’t force yourself to take it out since you might damage the tray.
Step #6. Drain the water
You can discharge the water to the sink and clean it if there are no signs of dents. Clean the tray with some bleach or vinegar and wipe it dry with a cloth. But ensure that when you replace the tray, there will be no excess water. Leaving the water undrained might emit an unpleasant smell.
Cleaning the area where you will put your tray is also part of this process. Also, examine if there are any leaks to check. Then, wipe the surface, especially when there’s excess water, and you can prevent the back or front of your fridge from smelling. And if the tray is not damaged and there are no leaks, you can place it back and reattach the back panel.
Closing Thoughts
And that is how to remove drip tray from fridge. Checking and maintaining your drainage system’s function is necessary, especially to the overall operation of the refrigerator and keep it clean. We don’t want to leave unstrained water inside the fridge and let it spill if there are any cracks on the tray. So, check or have it checked regularly. We hope this article has presented you with all of the information you require.
However, you should also check your manual for additional knowledge because not all refrigerators are the same.
Also, we mentioned a thing about air conditioners earlier, so if you want to know more about their drainage system, you can read this article about how to drain air conditioners. Keep safe!