How To Put Together A Queen Bed Frame? 5 Easy Steps!

Have you bought a queen bed frame, and you want to know more about “how to put together a queen bed frame?”

If that’s the case, you no longer have to worry about it. So we will help you with that one.

Queen beds are one of the most comfortable and spacious sizes of bed that one can have.

No wonder why you also bought one. Although setting it up might be more challenging.

If I were you, I would ask for a helping hand to make the process easier to finish and do.

But that does not mean that you can’t do it on your own.

If you are an independent person, you can do it on your own.

Just make sure you have enough knowledge on assembling a bed frame.

We have steps for you to follow, so make sure that you list them down and note them.

 

how to put together a queen bed frame

Steps To Put Together A Queen Bed Frame

You might have invested in a good-quality bed frame, and you might want something big.

Well, maybe those are some of the reasons why you chose to purchase a queen-sized bed frame.

Do not worry because we will give you specific instructions and a step-by-step one to assemble it perfectly.

It is important to figure things out on your own.

At least you are learning, but then you will always need a guide.

So, how to put together a queen bed frame?

You can use the following steps listed for your reference and guide as you assemble your queen bed frame.

 

Step #1. Prepare everything

This step is more likely the plan of everything before you assemble your queen bed frame.

Knowing that it is larger than the standard size bed frames, it is hard to transfer it from one place to another.

You have to remember that it will take a lot of time to disassemble and assemble it all again.

So, you want to plan where to place your bed.

Consider all the things you are preparing, especially the space in your room that can limit your movement.

 

Step #2. Prepare the rails

The next step would be about the rails you will have to lay on the floor before setting up the whole bed.

It would help if you placed it where it should be when the bed frame is already assembled.

By each railing, you will have to insert the legs of your bed frame.

But then, for first-timers, you have to follow this.

It would help if you grabbed casters then attach them by sliding their end on the leg of your bed leg.

To snap them out, you can use a hammer and do it slowly.

 

Step #3. The bottom and top rails

It is now time for you to attach your bottom and top rails.

Fold those arms in a piece.

That applies to both top and bottom rails.

You have to do this separately, considering each direction.

Pull the arms out and make sure that they reach that 90 degrees position, side rails as your basis.

The slots are where you will be inserting your arms.

That is identified by measuring your lots.

In that way, you can choose which one of these can be placed in your box springs that fit perfectly on your frame.

Right on your slots chosen, you can insert and lock your sidearm ends.

 

Step #4. Your center bar

When you check the side rails, you will see a hole halfway down.

On the of your center bar, there is also a whole. That has the same size.

You should align those holes on every end of your center bar and the sidebars appropriately.

Insert a bolt-on of the holes to hold and secure the center bar and the side rail together.

With the washer, you have to insert some nuts. Screw it in and use some wrenches to tighten them.

After doing this, you should see that center bars are attached firmly on the middle hole of each side rails you have.

Then you should add an end cap on each end of your frame to avoid a snugging bed on these pieces.

 

Step #5. Placing the footboard and headboard

This last step is one of the most important steps you will need to do.

You will add the headboard and footboard.

Check two holes at the end of your headboard.

Align these two with the holes on the back of one of the side rails.

You should then insert some bolts right through the holes, then add washers.

Just like that, use your wrench to tighten the nut.

Apply the exact opposite of your headboard.

After securing and tightening the nuts and bolts, you can proceed with the footboard doing the same process.

And that’s it!

 

Conclusion

And that’s the end of our article for today. We are hoping that you have learned a lot with us today.

With that, we have answered, “How to put together a queen bed frame?”

You now have an idea about it, and you can do it on your own.

Leave a Reply

Your email address will not be published. Required fields are marked *

No more posts found in this category.

[mailpoet_form id=”2″]