Are you wondering how to operate radiator heater? We know, you have a radiator heater at home, yet you do not know how to use it. Well, learn these manageable steps so you can operate them efficiently.
Radiator heaters are used to heat spaces, similar to other space heaters, but water is boiled down to create heat in traditional heaters. On the other hand, if you have a modern model of the radiator, which is electric-powered, don’t worry as you can handle radiator heaters easily and quickly!
Radiator heaters are not typical in heating spaces, but some buildings or establishments still have this heating system. You probably know radiator heaters heat, but if it’s your first time encountering this type of heater, as heating systems nowadays are wall heaters or baseboard heaters, you might find this one new to you. But, don’t worry, this article will help you, my friend. Let’s dive in!
Steps To Operate Radiator Heater
Three types of radiators also have different ways of operating them. On the other hand, the traditional heaters of the radiator, which produce heat from steam, go in a long way-the steam radiator heaters, unlike electric powered radiators. It means steam radiators need time or at least 30 minutes to heat your room while electrics is ready to use in 10 minutes. The water or oil must heat up to radiate the heat in a space. If you have a larger room, the heating time will be increased than the numbers. Operating a radiator is quicker than you thought, but you must do it correctly to avoid misuse. Hence, learning how to operate radiator heater is a must.
Step #1. Locate the dial valve
Usually, the switch of radiators is placed at the bottom of the radiator. If you did not find a valve underneath the radiator, then the dial valve must be at its side. The radiator dial or switch valve of the radiator may look like a valve o a valve that has a lockshield cap. If your radiator heater has a dial, you can turn on the radiator by spinning it. Do not turn the smaller valve control as turning this clockwise will turn off the radiator. Just turn the upper part of the dial.
On the other hand, if your radiator has a lockshield cap, test it out first if the cap is connected to the valve, Test it by pulling the cap, and if it pops, there is a metal valve, and you need to turn it counterclockwise using pliers. Meanwhile, if you notice that the lockshield cap is screwed, you need to loosen it first and remove the cap. Then you can turn it on by turning the metal like discussed earlier. For electric radiators, check your device if it has a plug-in wire. If it has, you can directly plug it in an outlet and look for an electric panel and press the “on” button to turn it on. You may also be interested to know about what do the number on a thermostatic radiator valve.
Step #2. Adjust the temperature
Most space heaters have a thermostatic valve to control the heat in a specific room. They are located at the opposite side of the radiator dial or below the dial. A thermostatic valve has numbers that range from zero to five. When the control is positioned at zero, there is no heat released in the room from the radiator. Meanwhile, the five represent the highest temperature of your device. Note that zero position does not turn off the electricity and water in your radiator. So, if you want to stop the radiator from releasing heat for a while, you can perhaps put the control into zero. If your radiator does not have a thermostatic valve and you want to control the heat, you can call a professional technician for your access.
Step #3. Heat the room
Most homeowners often make mistakes in setting the right temperature they need and usually set the thermostat into the highest and turn it into the lowest. To help you gain access quickly, you can set the thermostat in the middle and increase it slowly or decrease it, if you prefer. After choosing your preferred temperature, you need to wait for a few minutes until the room is thoroughly heated up. In electric radiators, it will take at least 10 minutes, while it takes up to 30 minutes for steam radiators.
Step #4. Frost setting
The frost setting can help you in maintaining your radiator heater. This function is helpful, especially if you live in cold countries that experience cold weather. Suppose you need to go out for a while and it’s winter. To help your radiator function well when you need them, you can set the thermostat in the frost setting and prevent the water or oils from freezing. The frost position is placed between zero to one, represented in either an asterisk or snowflakes. If you need to turn off the radiator heater, you can quickly turn it off by turning the control valve counterclockwise and pressing the “off” button in electric-powered radiators. To maintain the performance of your heater, you can set the temperature into the lowest setting before you turn it off.
It’s A Wrap!
Great! You have finally learned how to operate radiator heater by reading this article. Hope this helped you discover not only the function of the radiator hater but also the essential parts. Now that you finally know how to operate or use radiator heaters, if a building or establishment has this type of space heaters. You may also want to read about radiator heater how it works and what kind of heater do i have.