How to Mount Wheels on a Swivel Chair: A Tutorial

Swivel chairs are a great way to get some movement in your workspace, but how can you make sure that your chair is as stable as possible? One of the best ways to do this is by mounting wheels on a swivel chair. This article will show you how!

In this blog post, we’ll be going over how to mount wheels on a swivel chair or office desk. All it takes is a few tools and bolts and screws! We’ve also put together an awesome tutorial just for making sure everything goes smoothly.

how to mount wheels on a swivel chair

 

Steps on Mounting Wheels on a Swivel Chair

Step 1. Prepare your work area by laying down a towel and placing the hardware on top. You’ll also want to have another towel or rag close by in case you get any metal dust onto your clothes.

Step 2. Loosen all of the bolts, screws, nuts, washers and anything else holding your chair together with an Allen wrench (or similar)

Step 3. Carefully take off the old wheels and set them aside. You will need to drill a hole in each of your new swivel chair’s base plates and then screw on the bolts from inside so that they protrude outside through the drilled holes. When you do this, be careful not to cross-thread anything! If you do, you run the risk of damaging your chair.

Step 4. Slide on your new wheels and tighten them with a wrench or screwdriver (depending on how tight they are). If they’re loose, use some plumbers tape to secure them in place. These components must be tightly fastened so that no one will accidentally get hurt.

Step 5. After you have tightened your new wheels, use a drill to make holes in the base plates of each chair leg and then secure them with nuts on the inside of the legs. Again, be careful not to cross-thread anything! Take care as it can damage your furniture if done incorrectly.

Step 6. Finally, slide one foot onto the first chair leg, then thread the other foot onto the second. Then use a wrench to twist them on and secure them tightly in place with one bolt on either side of each wheel.

Step 7. You can also put some rubber furniture pads underneath your legs so that they don’t scratch up your floors if you’re worried about how deep those bolts will go into your floors.

 

How to Install Grip Ring Stem Casters

Step 1. Buy a grip ring stem caster from your local hardware store. The stem caster should be the same size as the screw holes on the bottom of your chair.

Step 2. Put one foot onto the first chair leg, then thread the other foot onto the second and tighten them in place with bolts on either side of each wheel. Repeat for the other side.

Step 3. Be sure to buy enough bolts for your chair, so that the caster is secure and in place with one bolt on either side of each wheel. You can also put some rubber furniture pads underneath your legs so that they don’t scratch up your floors if you’re worried about how deep those bolts will go into your flooring.

Step 4. Use your wrench to attach the caster’s stem to the hole in each of the chair legs, then tighten it securely with a spanner. Repeat for both sides and you’re done!

 

How to Install Caster Wheels on Office Chair

Mount caster wheels on an office chair with the following steps:

First, place your chair where you would like it to go. Make sure that there is enough room for how much space you need the casters to move in before deciding how far apart they should be.

Next, loosen both bolts at one end of a caster so that it can move back and forth.

Place the caster in the place where you would like it to be on top of your chair’s base, then tighten one bolt at a time until they are both tight again.

Repeat this process for how many casters you need, making sure that all bolts are tightened before moving onto the next caster.

Once all casters are on, tighten each bolt again in the order that they were loosened and make sure that it is tight before moving onto the other bolts to ensure there will not be any slipping while you are using your chair.

 

How to Dismantle Office Chair Wheels

One of the most common causes for office chairs to get stuck is that they have wheels on them. There are two ways how you can remove those pesky caster wheels: with a screwdriver or without one.

The first way how to take off your chair’s wheels will require the use of a screwdriver so if it doesn’t, then go ahead and use the second how to dismantle office chair wheels without any screwdriver.

All you have to do is unscrew each wheel’s bolt according to your table of instructions for how many screws it has (usually four) and take off all four bolts on one side.

For your chairs not to get stuck as they have before, be sure that when assembling them back together don’t tighten each bolt too much.