How To Measure For Pinch Pleat Curtains? 3 Best Ways!

The question is: how to measure for pinch pleat curtains?

New curtains can change the appearance of your room. It can also make it feel cooler or warmer.

how to measure for pinch pleat curtains

For instance, if you intend to hang pinch pleat curtains in your room, it can keep out the sunlight during summer and the cold air when winter comes along.

Not only that, but they can also make the window look larger than it actually is.

Depending on how you hang them, it will not obstruct the view outside the window when you open them.

With that being said, finding out the accurate measurements is crucial for it will ensure that the curtain can fit the window and result in the look that you are after.

But how are you going to measure the pinch pleat curtains?

Stay tuned because in this post you will be guided on how to get the right measurements.

 

Steps To Measure For Pinch Pleat Curtains For A Pole

Pinch pleat curtains can fit onto a decorative pole.

In this section, we will provide you a guide in measuring a pinch pleat curtain for a pole.

Before you order the curtains, know the width of the pole first as well as the length you desire for your curtains.

To begin you need a pen, tape measure, and paper.

So, how to measure for pinch pleat curtains?

 

Step #1. Outline the window on a paper

Label the width of the pole on top and the length of the curtain below.

 

Step #2. Start measuring how wide is the pole

Get the measurement of the pole’s full width but you must not include the finials.

Then take note of this measurement on paper.

 

Step #3. Measure the length

Now you have to measure the intended length of your curtain.

Start measuring from below the rings of the curtain up to the spot you like your curtains to end.

Your curtain may end anywhere you like. It may end just above the window sill, under it, or even on the floor.

Perhaps, you choose the latter, make sure to leave about an inch so that the curtain will end barely kissing the floor.

Do not forget to write on the paper the final measurement of the curtain length.

Then, use these measurements when you order the pinch pleat curtains.

 

Other Ways To Measure Pinch Pleat Curtain According To Type

Different pinch pleat type requires a different way to measure for it.

Below are some other ways on how to measure pinch pleat curtains.

 

#1. For Center-Draw

For this type of pinch pleat curtain, you need to measure across the window.

Include in the measurements the casing if there is any.

 

Step #1. In measuring

You have to measure straight through the window and not at an angle only.

Then ensure to write the measurement down.

 

Step #2. In deciding

Then you have to decide if you want the curtain to pull open showing the entire window.

If yes, the measurement you get from the first step must be multiplied by .15.

Otherwise, proceed to the next step.

 

Step #3. Will it be overlapping?

You also have to decide if you like your curtains to be overlapping in the middle when you close them.

If so, add four inches to the measurement you get in the previous step.

In case you skipped it, then just add it to the measurement you get in step #1.

But if you do not prefer overlapping drapes, proceed to the next step.

 

Step #4. In addition to the total measurement

The total measurement must then be added by eight inches to get the total width for the rod.

 

Step #5. Choosing your curtains

After getting the width of the rod, you may now choose your curtains based on that measurement.

 

Step #6. Get the length

Get the measurement for the length of the curtain starting from the top of the window down towards the point where you intend your curtain to end.

 

Step #7. Total measurement

Add four inches to your measurement to get the total curtain length that you need.

 

#2. For Side-Draw

In this type of pinch pleat curtain, you can start by following steps number 1 and 2 for center-draw curtains.

Then proceed to the steps below.

 

Step #1. What to add in your measurement

Add five inches onto the total measurement you get above.

 

Step #2. Follow the steps above mentioned

To complete, follow steps number 5 and 6 for center-draw curtains.

With this, you will be able to get the width and the length that you need.

 

Styling Tip

For pinch pleat curtain, it is recommended by designers to use traverse rods since it will let you open and close it easily by simply sliding it through a track system.

In case you already have a decorative rod installed on your window, you may use curtain hooks and pinch pleat rings.

 

It’s A Wrap!

How to measure for pinch pleat curtains?

Well, designing your window with the right treatment can enhance the look of your room.

With your simple, you can already transform a boring room.

But proper measurements place a big role here, so you must know how to measure pinch pleat curtains,

Most often than not, curtains are the biggest item one can find on the wall, so they can easily catch the eye.

Curtains that fit badly can stand out thereby causing the décor of a room to look unattractive.

As such, ensure to follow the steps above to prevent that from happening.