For someone who has a room with several windows, getting the right window treatments may be quite expensive and stressful.
Do not worry about deciding on the look you want your space to have and making it a practical DIY project if you don’t sew, as we will discuss in this write-up how to make curtains without sewing.
If you are also scared of needles, you don’t have to worry yourself because you may not even use the needle and thread while making these curtains.
You only need to seal your curtains in place with any bonding material, use clips and pins. All these devices and methods make changing your curtains at any time easy—no need to even see the rod pocket where you slide in the rod at the top.
When decorating a living space, people often consider drapes as the last thing to take care of. But when they are perfectly done, they impact the whole place greatly and transform the entire place.
The nicest thing about window treatments that don’t require sewing is that there’s flexibility in changing them frequently. They are so quick, simple, and cost-effective to make.
Steps to Make Curtains Without Sewing
When you plan on how to make curtains without sewing, you need to get the materials ready. The following items will be needed
- Enough fabric for your window, leaving some extra fabric at each side for the hems and also a fullness look.
- Curtain grommets
- Any bonding material; fusible bonding tape, glue gun
- Safety pins
- Tape measure, yardstick, or any other distance measuring device
- T-square
- A sharp fabric pencil
- Clips and clip rings
Step #1: Taking Measurements
The first step on how to make curtains without sewing is measurement. This is the important part of the making curtains procedure; this is because you don’t want to waste your fabric, especially if they are costly.
When two windows are close to each other and have a very small distance in between them, you should treat them as large ones with just one panel for each.
So when you measure, it would be easier—measuring the full width of both on the fabric and length. Ideally, curtains sit on the window floor, so you need to give the extra allowance to achieve this by adding extra eight inches to the length.
These extra inches include two inches for the bottom hem and six inches for the rod sleeve at the top.
Step #2. Cut your fabric
The next step on how to make curtains without sewing is cutting. When you are cutting out from a large quantity of fabric, achieving a straight line across may be difficult, and you need even lines to get an even hem.
If you have a crooked bottom from cutting your fabric, it will give your curtains an off and unappealing look.
You can use a T-square as a solution, but if you can’t get one, set your cutting line by measuring the regular points across the fabric for the length and forming marks along, then you cut by connecting these marks.
Step #3. Tape The Edges
Although this is optional, at this level, you can proceed to fold a hem down on your fabric. However, you may want an additional layer of protection from frayed edges; then, you would better fold the edge first.
For you to do this, on the backside of the fabric, lay a line of tape or use your glue gun on the edges, peel off the backing of your tape, and fold over the glue. You would have for yourself a clean edge.
Step #4. Tape the hem
You can make the hem. Measure your hem using a T-square or the creating and connecting the dots method you used for cutting.
Lay out the tape along the line you created, or use a glue gun, peel the tape’s backing and fold the edge of the fabric over the glue or tape.
Press your fabric firm to make sure it is tightly secured into place. Do this for the bottom and on both sides of the fabric but not for the top.
Step #5: Create the rod Pocket
Since you will create your rod pocket on the top, that is the part of the fabric which you will fold over to allow the rod to slide into. Measure the rod to use, mark the width on your fabric, adding another one or two inches from the top edge.
Apply the tape or use a glue gun, then fold and press together tightly.
Step #6: Hang your curtains
The last step on how to make curtains without sewing is hanging your ready curtains. After having your panel, you should hang it! From the rod brackets, remove the rod and slide the panel into place. Ensure that they bunch evenly on one side.
Put the rod back in its brackets and screw the finials, drop your curtains, and there you have it!
How High Should I Hang my Curtains?
Normally, it is a well-known that curtains should hang about 4 inches to 6 inches higher than the window frame. Therefore ensure that you fix the curtain rods accordingly; it makes the window look higher when you hang your curtain rod high.
What is the Best Fabric to use for Curtains?
When deciding on your curtain materials, go for velvet, linen, silk, and faux silk. They look appealing for your window treatments, so they should be your top choice.
Conclusion
DIY curtain ideas do involve using a huge range of methods and styles. Some of the steps you can complete in hours or less than an hour. At times, it does not require sewing knowledge, which is to most people’s excitement.
You should determine the set of curtains that will go well with your space and be inspired to learn how to make curtains without sewing!
The benefits of making your curtains will save you some money because the curtain fabrics do not have a rebranded identity yet, so they come cheaper.
As a result of this, you can include different designs of pleatings for your curtains, which will make you control the look your curtain fabrics will give you draping from the top to the floor.