How To Make A Room Heater? 6 Easy Ways!

Are you looking for the answer to the question: how to make a room heater? My friends, you have reached the right place; this article will tell you about six easy methods or ways through which you can quickly know how to do so. 

It is necessary to keep the room warm during winter, but because it’s quite expensive, most people cannot purchase a heater.

How to make a room heater

Don’t worry if you can’t. Below are some easy methods that you can easily do to make a room heater on a low budget without compromising its quality. So, without further ado, let’s start!

 

Ways To Make A Room Heater

Following are the six easy methods on how to make a room heater:

 

#1. Stoneware candled heater

You need some candles, a small fan, a ceramic spot, four bricks, and a tray in this method. Firstly you take 5-6 candles, put them on a tray, and let them blow up. Now take the four bricks, put two of them on either side of the tray, and the rest of the two behind the tray. Then cover your candles through a ceramic spot. The position of the ceramic spot is upside down on the tray and above the candles. Now position the small fan behind the tray and above the bricks. Then turn on your small fan. Finally, the stoneware candled heater setup is completed.

 

#2. 100W-12V Mini room heater

In this method, you need some screws, a tin can or box, wet black clay, a cardboard piece, two coil wires one is medium size, and another one is small (resistance=3-3.5 Ω), insulator, and power supplier 12V. First, you have to take the tin box and hole it using the insulator drill. Put the insulator in it and fix it by using screws. Place a cardboard piece in front of the insulator, which is present in the tin, and add wet black clay to it. Now place the coil in this wet clay and leave it for 24 hours to dry black clay. After 24 hours, join the coils with an insulator and connect the power supplier with an insulator. The setup is simply completed, and the coils start heating up.

 

#3. Solar can heater

To make a solar can heater, you need about 300 aluminum cans, a sheet of plywood (about 4ft. × 8ft. inches), Plexiglas (about 4ft. × 8ft.), black spray, a plastic tube, wood for the frame, air blower and high-temperature silicone. First, you have to make about 4ft. × 8ft. 3.5 inches wooden frame. Then nail the plywood on the back of the frame. Now make two holes in the frame. One is at the top, and the other is at the bottom using a drill. Also, hole all cans at the top and bottom. Then place the top hole of the can in the bottom and make about 16 rows. 

Now seal these joints by using silicone caulk. After drying silicone caulk, you can paint it using black spray paint. Place this column can bottle in the wooden frame and the whole structure with Plexiglas. Now drill two holes in the room one is near the floor, and the other one is near the top. Then by using a plastic tube, you can connect the hole of the room with the hole of the wooden frame. In the end, you can put the air blower at the bottom and top of the pipe. Now your solar can heater is ready. It may be helpful to read about benefits of using solar thermal heating.

 

#4. Alcohol heater

Making an alcohol heater is also the very most straightforward method. You need 70% isopropyl alcohol or rubbing alcohol, metal cans, and toilet paper rolls. As it is a straightforward method so, first you have to take a toilet paper roll and put it into the metal can, then pour the 70% isopropyl alcohol into a metal can and finally ignite it; that’s it.

 

#5. Tabletop fire pit

In this method, you need a ceramic container with a fire-resistant or concrete bowl, rocks that are also fire-safe, and can. Firstly, you have to take your fire-resistant container or concrete bowl and make a layer of fire-safe rocks inside this container. Consider that this rock layer is not too tightened because the airflow is necessary to escape the hot air from the container. Finally, add fuel to the container and add more rock layer if needed and ignite it. Your tabletop fire pit is ready.

 

#6. Rocket stove

For this method, you need cans (different sizes large, medium, and small), a metal cutting saw, leaves or twigs for a fire, matchstick, screwdriver, permanent marker, sand, and gravel. Firstly, place the small can inside the large can (main can) and make a line with a permanent marker. Cut it by using a metal cutting saw. Convert the sharp edges into smooth ones utilizing a screwdriver. Now cut the bottom of the little can and fit it inside this hole, and fill the main can with sand and gravel, which is considered an insulator. Finally, put the twigs from the spot and ignite them. The heater is completed, and the smoke comes from the top of the heater.

 

It’s A Wrap!

Now you know the answer to How to make a room heater. You can follow the methods mentioned above for making a room heater. I hope this article will help you a lot. You should also know about electric heater repairing. Don’t hesitate to know these things too; read about what is the best space heater for a large room and what is the best type of heater for a room. Thank you for reading. Have a great day! 

Leave a Comment