Making a bow for a bassinet can be a daunting task for newbies. We have compiled a step by step guide on how to make a large bow for bassinet bumper
Steps on How to Make a Large Bow for Bassinet Bumper
Step One: Gather materials needed for this project. You will need scissors, a piece of paper that is twice the width you want your bow to be, and tape or glue (for attaching ribbon).
Note: If using tape instead of glue you can skip step two below as well!
Step Two: Fold down one inch at both ends so they meet in the middle with right sides together. This makes what are now the inside folds
Step Three: Now fold over again along line AB; repeat on another side (now lines AC & BD) making sure all edges remain even. Staple seams closed if using adhesive or secure by hand stitching otherwise (Advantages/Disadvantages of Using Tape vs Glue – The Advantages of Using Tape: Easier and faster than glue. – The Disadvantage of Using Glue: Might not hold if the bow is outside in the wind for a long period of time)
Step Four: Place the piece on top where you want your ribbon to be, then fold over once more (E & F); staple or sew together
Note: You can follow these steps with any width paper (Advantages/Disadvantages). However, I would advise against using anything less than one inch as it will make stapling difficult. It also might require two pieces instead which could look odd after the bow has been attached!
For Example: If you were going to use an eight-inch piece of paper (four inches on either side of the bow), you would start with step one.
Steps on How to Close Chicco Portable Bassinet
Remove the mattress from the bassinet and place it on the floor or flat surface. Gather all four sides of the cover around to the bottom centre, ensuring they are even. Fold in half diagonally across bassinet base, making two triangles at top corners.
Flip down covers below where you folded them over. If there is a second set of buttons near the base of each wheel; they will pop out – push these back into holes by pushing one end through first then pressing another side until it clicks firmly into place.
This step ensures that your folding mechanism stays put so be sure both sets click securely before moving forward! For added security, if needed pull any strings up along the edge next to the zipper towards the outer edges of the bassinet. You should now have a fully zipped, folded up and secured bassinet you can easily transport from room to room or take on the go!
Steps on How to Set Up Your Kolcraft Cuddle N Care Bassinet
Step One: Gather Materials What you will need is all of the parts included with your bassinet, and a screwdriver to put it together.
Step Two: Assemble Frame Next we open up our frame box. The first step in putting this baby bed together! Make sure that all pieces are accounted for before moving on; if not call customer service immediately! I know having lost screws can be frustrating so make sure everything’s there first (if not – complain!).
This part is pretty self-explanatory but always good to go over anyway 🙂 We want to start by inserting each metal bar into its corresponding hole making sure they’re secure before doing anything else. Then simply snap on both ends until snugly secured.
Note: if you’re having trouble with this step, make sure that the holes are lined up correctly. Even though they look like they will fit – sometimes one side can be larger than another and prevent them from locking into place properly.
Step Three: Attach Velcro Our next step is attaching the mattress to our frame (if it isn’t already). With both pieces together we’re ready to attach velcro around the perimeter of each board!
This part’s important because it ensures a snug fit for your baby so don’t skip out on getting these puppies attached at all corners 🙂 Place half of your first strip diagonally across one corner; Then go back over top with the second piece making sure not to overlap the previous section by at least an inch or so.
Steps on How to Crochet a Baby Bassinet
They to be able to create the bassinet of their dreams. The following steps are simple, easy and short for anyone with some experience in crochet know-how who wants a baby-sized project that is fun, fast, and rewarding.
Step One: Gathering Materials You will need five plastic pony beads (one bead each), two buttons or snaps which you can use as ties on either side of the bedding when it’s not being used, one ball size six steel crochet hook, yarn needle for finishing off your work at home after you’ve completed the final step in making up these amazing pieces!
A word of caution though – if you’re still learning basic stitches like sc and dc they may cause issues but by far this isn’t an advanced pattern. One last thing to note is that you need your own measurements of the headboard, footboard and mattress size before starting this project!
Step Two: The Headboard First I start with making a slip knot on my hook (not too tight) pull yarn through the loop loosely for about eight inches then make another stitch into that same space next I will single crochet around all four sides in one continuous round until it’s big enough (about six inches) and then I cut the yarn (leaving a long tail for sewing on to mattress later) I pull it through my loop and tie off.
Step Three: The Footboard To make this part you will again want your slip knot around eight inches from a hook or whatever is comfortable, single crochet all four sides in continuous rounds until about six inches high (this time do not tie off).
Now flip it over onto its backside so that the two headboards can be attached by their corresponding footboards using whip stitches. Once they’re joined we will begin stitching them into place at the bottom of our bassinet mattress!
Step Four: Finishing Touches With both pieces stitched securely down we turn our attention back inside where we will attach our mattress. I like to use the thin foam bumpers you get at most baby stores, but anything of equal thickness will do!
We also want this piece slightly smaller than both headboards combined (about five inches less on each side). After that is done we need to staple or hand sew a thin fabric lining around all four sides leaving about two inches for an opening along one end.