How To Install Air Conditioner In Wall? 6 Easy Steps For You!

Are you having a hard time trying to figure out how to install air conditioner in wall? In six simple steps, you can; worry not about that already because we will help you.

Today’s weather is so that even your fan cannot fend off the heat from your body and the sun itself.

And that is if you are going to buy a new air conditioner for your house or room, though you do not have any ideas on how some people do it correctly, right? That would be a problem if you did it without any guide or supervision.

So to help you, we have prepared some basic steps that you might want to put to use. Also, when dealing with air conditioners, try to handle them with care as much as possible as they are cumbersome to carry all by yourself and are expensive.

To avoid this, stay with us until the end of this article to know what air conditioners are and how we could install them.

 

Steps To Install An Air Conditioner In Your Wall

How to install air conditioner in wall? Below are some steps you may put to use that may require a significant amount of money to be spent; this is for you, so do not worry cause it’ll be worth it.

 

Step #1. Gathering all the needed materials and tools

Before moving on to the next step, you’ll need to gather all of the required tools and materials to be used later on. Below is a list of items that are required to complete it; here are the following:

  • Sleeve
  • Measuring tape
  • Stud finder
  • Paint
  • Marker
  • Pry bar
  • Circular saw
  • Hammer
  • Level
  • Drills and drill bits
  • Utility knife
  • One sheet of drywall
  • Drywall compound

They may be a lot, but yes, these are what you need to finish installing your air conditioner with an aesthetic touch to it. Another reason you should consider when working using these tools is to finish the job neatly without damaging anything. Now let us move on to the next step so that we can be able to finish it later on with ease and quickly.

 

Step #2. Choosing your desired area

Let us start by looking for an excellent area to easily attach and reach your AC for usage whenever you need it. It would help if you had to consider spots where you think it would fit in properly and keep it close enough to an outlet without hassle.

Also, the bottom of the wall AC unit should be around 1 to 5 feet above the ground. That will reduce the quantity of dust collected by the air filter.

 

Step #3. Marking and locating the studs

After you have decided where you want your appliance to go, you will need to mark the studs to know where to start when cutting through the drywall. You’ll need to use a stud finder for this one to identify where the spots are accurate.

Now once you have located three to four studs, mark them on the drywall. After that, you’ll then want to measure the width of your air conditioner and move it to the wall where the studs were indicated.

In that way, you could easily distinguish the size needed for the walls to be holed so that you can put the appliance inside of it. While doing this, make sure that you turn off the power to get shocked while doing.

 

Step #4. Making the hole for the unit

For this step, you want to make sure that you have an outline that is the same size as the unit to fit into the hole. Also, make sure that you should straighten the sleeve.

Use the level if needed for a more accurate hole. Then, it would help if you made an extra outline that is quite bigger than the first one for the supports to snuggle into place.

Now score the outline using your knife, then using the hammer to knock the center part of the scored drywall sections so that they pop out easily. You have to take out your saw and cut through the studs inside so that they are flush with the outline.

 

Step #5. Making the frame to hold the appliance

Once you have measured the opening dimensions earlier, transfer it to the lumber and begin cutting it down until it matches the length of the outline. Now put all the pieces together, and there you go, you now have a frame to hold your AC.

 

Step #6. Creating a hole for the exterior and installing the unit

Finally, use a drill to start making holes in each corner of the marked areas earlier, then, on the external wall, draw at least four straight lines to link the drill holes.

Use a saw to cut through the materials so that you have a leveled hole in its interior and exterior parts. When you’re finished, put the metal bracket that will hold your appliance on the exterior in the sleeve and fasten it to the frame.

Plug it afterward to the outlet. And there you go, you now have your newly bought AC installed and is ready for use; final touches are all up to you if you want more aesthetics for it to look good.

 

Conclusion

Now, because you have the idea how to install air conditioner in wall, you can start and try to do it on your own. But if you are still hesitant, it would be best to call for a professional to do the job. For more articles like this, click here. That is all.

Leave a Comment