How To Hang Curtains On Concrete Walls? 2 Best Methods!

How to hang curtains on concrete walls?

Hanging draperies or installing curtains onto the concrete wall can be very challenging to do.

That is especially true if you do not have the proper hardware and tools.

The installation process is very much like the drywall application.

It is challenging but attainable.

For as long as you have the suitable anchors and tools, you can complete the mounting process of the curtain brackets in a couple of minutes.

 

How to hang curtains on concrete walls

Methods To Hang Curtains On Concrete Walls

You can hang curtains by drilling the concrete walls for the hardware.

But if your rental place does not permit you to create a hole in the wall, you might as well resort to the following method that does not require drilling.

Here are the methods on how to hang curtains on concrete walls:

 

Method #1. With drilling

Below are the steps to follow if you opt to drill curtain hardware on the concrete walls.

 

Step #1. Position your mounting hardware on the spot where you intend to install them

You have to measure the height of the brackets to ensure that the rod will be level.

Mark the positions of each screw hole on the wall for the mounting hardware using your pencil.

 

Step #2. You have to lock a carbide masonry bit into the drill

Remember that the bit must be big enough to create a hole that can securely accommodate the anchors.

Do not forget to wear your safety goggles before you start.

 

Step #3. Position the bit’s tip on the mark on the wall that you made in the previous step

Now hold the drill with bit positioned horizontally,

Set the drill set onto its slow speed setting and start drilling a pilot hole first.

The hole must be a bit longer than your wall anchors.

Gently tap or press the wall anchors towards the pilot hole using a hammer so that you will flush its opening onto the wall.

Repeat the same process in drilling more pilot holes and installing the remaining wall anchors.

 

Step #4. Finally, position the brackets.

Ensure to align all of its screw holes with the wall anchors.

Pass through the mounting screw tip into the bracket and the anchor. Then, tighten the screws.

Repeat the process to ensure that the rest of the mounting brackets are securely attached.

After you have installed all the brackets, you can already hang the curtains on the curtain rod.

Then, hang those rods onto the mounting brackets you just installed.

 

Method #2. Without drilling

In case you are here to look for a no-drill method in installing curtains, you can use a spring tension rod.

They come in an array of lengths, colors, and designs.

This type of curtain hardware is very easy to install.

You can use it in any room from your house, and it will help you create an aesthetically pleasing look without the need to drill.

Below are the steps in mounting this curtain hardware.

 

Step #1. Measure the window area

You have to measure the area of your window first.

Take note of the measurement.

 

Step #2. Start measuring the length

Do this process from where you intend to mount the tension rod up to where you desire your curtains to fall.

You will have to choose from three different options here.

The curtains can provide a swag treatment onto the tension rod, reach the room’s floor or fall halfway.

 

Step #3. Mark the spot on your wall where you intend to install the rod

That is to make sure that it will be able to conform to the design of your curtain.

Use your pencil for this.

Then, twist the middle of the tension rod to unscrew it. Continue doing so until you have fully extended it.

Slide the curtains onto the tension rod and hang it after ensuring that the rod is already secured in place.

 

Step #5. Raise the rod and the curtains

Do this process into their desired position at the wall. Squeeze the tension rod to the center.

This one can trigger its spring as well as compress the rod.

As a result, it will fit snugly in place.

 

Step #6. Form a swag effect on the rod

Do this process by spotting its mid-point and folding the curtain in half.

Wrap the curtain around the curtain rod once and dress the fabric onto any of the rod’s ends.

You can even experiment to create more designs. For instance, you can pull the ends of the curtains gently.

Remember that the more you tug, the swag will be shorter and shorter.

 

Other Window-Treatments That Won’t Damage Your Walls

  • Using temporary command hooks
  • Hanging curtains using a tension rod
  • Create Faux Roman shade
  • Ordering custom-made compression shades
  • Suspending the curtain rod from the room’s ceiling
  • Purchasing Twist and Fit curtain rods

 

It’s A Wrap!

People find concrete walls attractive because it provides a modern feel into the room.

However, it makes hanging curtains a bit difficult.

Nonetheless, it would be best not to allow your concrete walls to achieve the look you want.

For as long as you have the materials and you know what to do with them, it is possible to hang curtains on concrete walls with ease.

That is how to hang curtains on concrete walls.

how to make your own without sewing

Easy Window Curtains: How to Make Your Own Without Sewing

Window treatments can be expensive, but luckily there are many ways to save money on your window curtains. This article will show you how to make your own without sewing!

 

Steps on Make Curtains Without Sewing

Step 1. Buy fabric and a rod that matches the size of your window. You will also need to buy some pins, an ironing board, scissors, measuring tape or ruler, and something to make a hem (such as thread).

Step 2. Measure how wide your curtains should be by adding two inches on either side for hems. The height should be the length of your window.

Step 3. Buy one yard of fabric for every panel that you want to make (e.g., if you are making three panels, buy three yards). Also, measure how wide and long your curtains should be by adding two inches on either side to account for hems. The height will depend on how many windows and how long your panels are.

Step 4. Cut the fabric to size for each panel of curtains and hem any edges that need it by folding over once, ironing flat, then pressing with a hot iron. You can leave them raw if you want an unfinished look which is what I did here.

Step 5. Take one piece at a time and pin it to the top of your window, leaving room on either side for how wide you want it and hemming.

Step 6. Begin sewing around the perimeter with a straight stitch, moving from left to right or right to left. You can use an overcast stitch if you have thicker fabric that needs more support. Be sure not to sew past where your panel ends.

Step 7. Repeat with the remaining panels and leave your curtains open until it’s time to hang them up!

 

How to Wash Curtains

  • Wash in cold water on the delicate cycle and dry flat. You can also take care of light stains by spritzing with a stain remover or vinegar before washing.
  • For more stubborn stains, soak the curtains in water mixed with a little detergent and stain remover for 30 minutes before washing.
  • To remove dust, vacuum the curtains or shake outside.
  • Avoid washing your curtain with a load of towels as it could fray or cause shrinkage in some fabrics.

 

How to Hang Curtains

Hanging your curtains can be as simple or elegant as you want them to be.

Hangers: You can use a variety of hangers for different looks, including plastic sticks in shower clips, clear clothespins, and fabric loops.

Rods: Basic curtain rods are perfect with most fabrics but if you have heavier fabrics, use a metal rod.

Hooks: Hang hooks at the top of your window frame, then simply hang your curtains over them.

Rod Pocket Cords: You can use these to hang your curtains without sewing. They provide a cleaner, more finished look and they’re good for heavier fabrics that won’t stay on regular hooks.

Tiebacks/Cord Loops: These are great for short windows with no rods or if you don’t want the hassle of installing anything else. Just tie them to the top corners of the panel.

Ropes: Use these if you’re looking for a more natural look and feel. You can attach them to your window frame with eye hooks, then hang your panels over them in any way that works best for you (hanging one on each side or hanging both from one side).

Tension Rods: These are best for short windows. Just place the rods on any side of your window, then hang one curtain over them and use a tension rod to keep it in place (you’ll need two).

 

How to Preserve Curtains to last long

Hang your curtains in a way that they won’t touch the floor or ground. This will ensure you don’t have to replace them because of mold growth.

Wash your curtain at least once every three months with water and detergent, then hang it outside for some fresh air before storing it away again (you can also use a dryer sheet).

Store your curtains at room temperature in an area with good air circulation.

If you’re storing it away for the wintertime, make sure to put them in a sealed plastic bag or container that will keep bugs out. Make sure to give them time before using them again by airing them out outdoors.

 

The Benefits of Window Curtains

  1. They’re a great way to get privacy in your home without taking down the curtains. Privacy helps keep both sunlight and light from outside sources out, which can help you sleep better at night by reducing how much artificial light is spilling into your bedroom.
  2. Window treatments add an elegant touch to your home. Curtains are a great way to liven up any room in the house or can be chosen for how they coordinate with the colors of your furniture and other decor pieces that you have.
  3. They’re also an easy way to change the feel of your windows without having to spend too much money! Window treatments can be swapped out with the seasons, to add a festive feel during the holiday season.
  4. Curtains are also an easy way to make any room in your home more inviting and welcoming!

[mailpoet_form id=”2″]