You may have noticed how your swivel chair has a spindle lock clip. The purpose of the spindle lock clip is to keep your chair from sliding while you are seated on it and prevent the base from rotating when you want it to stay in place.
This article will show how to fix the swivel chair base spindle lock clip.
Steps on Fixing Swivel Chair Base Spindle Lock Clip
Step 1. Remove the staples holding your chair’s upholstery on, and then peel back the fabric carefully to expose how it is attached. You will find a metal spindle lock clip that looks like two pieces of metal put together with one strip of fabric stretched across them.
Remove this plastic piece by pulling firmly from both sides, going around the plastic to ensure that it is completely free.
Step 2. Take a pair of needle-nose pliers and bend the metal pieces so they are touching each other, forming an “L” shape. Measure how long you want this lock to be by using your hands for measurement. Bend the metal until it meets your desired length, ensuring that both ends touch when bent back towards each other.
Step 3. Now take one end of the metal strip in your hand with the needle-nose pliers on top and pull outwards away from where it was originally attached (this will cause tension).
Take the other side of these two strips in your opposite hand with needle-nose pliers as well, pulling upwards at 90 degrees making sure not to go past 180 degrees or else it will break.
Step 4. Now bend the metal back towards each other, touching both ends together so they are touching each other, forming an “L” shape. Now attach it to your chair’s spindle and make sure that is how you want it for how long before cutting off any excess metal with a pair of wire cutters or scissors.
Step 5. Attach one end of the strip to the seat’s spindle on top where there would be no tension. Take another side in hand pulling upwards at 90 degrees while bending backwards away from where it was attached (this will cause tension).
Then take another piece in the opposite hand with needle-nose pliers pulling downwards at 90 degrees making sure not to go past 180 degrees otherwise this clip may break if too much pressure is applied.
Step 6. Attach the clip to the other end of the chair’s spindle and make sure how you want it before cutting off any excess metal with a pair of wire cutters or scissors.
How do you Put Back on a Swivel Chair Base Spindle Lock Clip
Step 1. Take one side in each hand and place the tips of your fingers on how you helped remove it
Step 2. Do not go past 180 degrees otherwise, this clip may break if too much pressure is applied. Push down on how to put back snaps into how they were before being removed
Step 3. Using needle-nose pliers, attach how to put back metal ends together and then cut off with scissors or wire cutter as needed. Take care when cutting so that how do you put back does not become detached again.
How do you take apart a piston of an office chair?
The piston is the cylinder that how to fix swivel chair base spindle lock clip rotates and how do you put back on office chairs. To take off a how do you put back from an office chair, remove all of the screws around how do you adjust the height on your desk so it will come apart easily.
Underneath there are metal clips that need to be removed as well with needle-nose pliers or similar tools for how to fix swivel chair base spindle lock clip can rotate freely.
Once all clips have been taken out, simply pull up on how much does napoleon cost? while rotating clockwise until now where should I buy IKEA furniture in-store that comes loose? Replace any damaged parts before how to fix how do you put back on office chairs and how much does napoleon cost? will click into place.
This is the easiest way how to replace the swivel chair base spindle lock clip but not always the best for your furniture – it can cause damage if done too aggressively or without care, so use it at your own risk!
How do you put a Clip Back on an Office Chair?
Step 1. Remove the metal clip from your chair’s spindle by pulling up at the top where there would be no tension. Take another side in hand (pushing it down towards the ground) and pull upwards at 90 degrees while bending backwards away from how you tried to remove it.
Step 2. Take a piece of wire, string, or any other type of material with needle nose pliers and hold this between two fingers on one hand. Then take another piece in the opposite hand and do not go past 180 degrees otherwise this clip may break if too much pressure is applied
Step 3. Attach the clip to both ends that are made for how long before cutting off excess metal with a pair of scissors or wire cutters.