If you’re thinking about the steps on how to disassemble the LG dryer, you need to follow these steps carefully. The disassembly of an LG dryer is not difficult, and with the help of this instruction. That is why this article was intended to assist you in disassembling your LG dryer.
Dryers are instead essential appliances, so with a bit of help, you’ll be able to fix your dryer in no time. Please note that this article is exclusively for LG dryer disassembly.
Setscrews may be used to secure knobs to their bolts. Remove the knobs by loosening the bolts and pulling them straight out. Only remove the rear panel to have access to most of the parts. If you can’t do the tests, replacements, or repairs from the rear, don’t disassemble the remainder of the cabinet. Remove the light from the dryer if it has burned out. You may need to remove holding screws and panels to get to it. Let’s check it out!
Steps To Disassemble The LG Dryer
Sometimes disassembling becomes very hectic but using the correct steps makes your disassembling process easier. Then, if necessary, replace any retaining panels. Many users of lg dryers are not aware of disassembling the dryers, but when you read these steps, you will come to know everything about disassembling. Now, here are the steps on how to disassemble the LG dryer:
Step #1. Taking off the front and top of the dryer
Turn off the dryer’s power. This is for safety reasons, but the heating element will be sorted out if you remove an lg dryer without disconnecting the power. Pull off all the screws from the front and top of the dryer. After removing the screws, lift the lid up and off. The front should pull forward once the screws are removed. You can either separate the cables from the door switch or swing the front to the side without you Are you Removing the connections at this stage? You’ll have to detach the wires if your dryer doesn’t have enough slack in the cables to do this.
Step #2. Taking off the drum and belt of the dryer
Raise the drum and reach beneath it to detach the belt. It’s worth noting that specific versions feature a back access panel that allows you to separate the belt from the back if it’s more convenient for you. If you’re working on an older lg dryer, an e-clip on the back holds the drum shaft in place. On the rear, in the center, there will be an access panel. Start by removing it and the e-clip as well. After loosening the belt, the drum should go forward and out. Start pulling the drum up and out of the dryer. You’ll have access to everything now that the dryer has been dis. It may appear that the drum will not come out of the case; nevertheless, you may need to spread the case open slightly to allow the drum to emerge.
Step #3. Taking off the blower wheel and motor of the dryer
Lift the vent cover to allow access to the blower wheel. Remove the blower wheel by loosening the screw that holds it in place. The blower wheel should be detachable from the motor shaft. Once the screw is loose, remove the motor by removing the clips that keep it in place after the open-wheel.
Step #4. Taking off the optional blower wheel and motor
For the people using older lg dryers, you must read this step for disassembling the dryer. Remove the blower wheel by loosening the screw that holds it in place. Remove the motor from the blower wheel housing by loosening the clamp that keeps it in place. On the rear of the motor, loosen the clamp, remove the engine. If you need to replace the blower wheel, you must first remove the open wheeling by loosening the screws from the rear.
Step #5. Taking off the heating element of the dryer
Pull off the dryer’s rear panel. Remove the cabinet top if required. Remove the duct’s screws. Place and disconnect the leads. After that, remove the complete heating unit from the dryer. Remove the screws holding the heating element in place in the duct. Replace the heating element in the heating duct in the same manner that the previous one was removed. Make sure the resistance coils aren’t damaged. Reconnect the lines, replace the screws that hold the vent’s heating element, and reinstall the unit. You may also want to read about how do I fix my LG dryer that won’t heat.
Step #6. Taking off the control panel of the dryer
Remove the screws that connect the dryer’s control panel to the cabinet top or front to remove it. These screws may be hidden behind a piece of metal or plastic trim; pull the edge off or loosen it to reveal the screws. The majority of knobs are friction-fit, so simply pull them directly out. Know how to remove the control panel from the Whirlpool duet sport.
It’s A Wrap!
We were delighted to know that all of you will come to understand how to disassemble the LG dryer. We hope you have learned everything in this post and can easily understand all the steps related to this topic by reading this article. Thank you, friends, for sticking with us! Click on these links to read related articles; know how to fix a dryer that wont spin and why my dryer wont spin.