Do you wish to learn how to convert a gas dryer to propane? This article will assist you in understanding the conversion process in easy steps. It’s simple to convert any gas dryer into propane.
All you have to do now is switch the regulators or change the orifice. Inside a conversion kit, there must be brand-specific guidelines. The equipment could be purchased at a nearby electrical repair shop. The methods for converting the gas dryer to propane are described here.
Many gas appliances on the market are established for natural gas. This is because most people live in places where natural gas is available. It’s not hard to convert a home appliance to propane and can save you roughly $85. I’ll explain converting the gas dryer to propane, so keep reading this article.
Steps To Convert A Gas Dryer To Propane
Converting a gas dryer to propane is not tricky, but it becomes dangerous if you are not doing the conversion process properly. Below are some steps that will help you understand how to convert a gas dryer to propane.
Step #1. Locate the burner chamber
Begin by locating the gas dryer’s burner chamber. There seems to be a small access door on the bottom right-hand side of most versions. Access panels should be removed. That’s on the left side for some models. Some will have the whole frontal board eliminated. There would be a few screws on some versions, while there’ll be none on others. You’ll have to check closely at the dryer to figure out where the chamber is.
Step #2. Locate gas controller
Go to the right side after removing the access door for the gasoline control valve. A little gas shutoff valve will be installed directly on the gas supply route. Pierce the pipe with the handle. The gas will be turned off as a result of this action. A wire can be found on top of the gasoline controller. Remove the quick connections and unplug them. Remove the hex nut from the control valve by loosening it. The hexagon nuts will also have a reversing thread, which means you’ll have to crank it counter-clockwise to tighten it and reduce it. Once you’ve removed the pipe, you’ll notice some metal sheet screws keeping the control plate in place. Remove all screws. You may also be interested to know about the gas dryer not heating up.
Step #3. Take this burner out of the gas dryer.
Its burner must be removed only enough to preserve the wires connected to the gas dryer’s flame sensor. The burner is attached to the shrouded cover with this. The wire will be quickly disconnected. Disconnect the cables.
Step #4. Orifice must be change
Eliminate the burner component next. The brass or bronze aperture can be found in the burner jet. Its BTU and the registration number or model may be found on the manufacturer plate. The gas dryer typically produces 19,000 to 21000 BTUs. For that rating, you’ll need to build the necessary propane orifice.
Step #5. Here on the gas dryer, flip the tower caps.
Its regulator is converted whenever the tower top is turned over. The gasoline kind it is established to utilize is indicated on the side of the lid that faces you. Natural gas would be labeled (N or NAT) for the time being. A cap on top of a tower must be marked (L or LP) for propane whenever you detach it or rotate it to reinstall it. Reconnect the power, light the pilot, and the gas dryer now becomes a propane dryer.
How To Check If Your Dryer Is Natural Gas Or Propane?
Natural gas is used in some gas-heated dryers, whereas liquid propane from a tank is used in others. Its inner burners for the two kinds of gas have distinct pressures, heating effects, or design possibilities. Propane-gas-powered dryers typically use a larger nozzle than conventional natural gas pipe couplings for safety purposes. To know which type of fuel to operate, devices must be labeled with the burners rating information somewhere else on the dryer. Inspect the household supply of gas to determine if the dryer is already connected.
Turn the knob and lever clockwise to shut the gas flow valve in the home. The device uses liquid propane gas if it has been linked to a tank on one side and the dryer on another. Your dryer utilizes natural gas if you are connected to a utility service. To find the burner’s characteristics, unscrew its front dryer door and look within the gate well. If somehow the dryer is intended for propane use, the burner kind would be specified as LP. Aside from that, it’s a natural gas device. When checking the gas connection, remove the dryer from the wall. Find the 3/4″ pipe which goes to the dryer’s back.
It’s A Wrap!
We are delighted to know that you have learned how to convert a gas dryer to propane. You should just follow the steps mentioned in this article to start converting process. But it is better to hire a professional plumber to do this for safety reasons. You may also want to read about how to check thermal fuse on dryer and what amp breaker for dryer. Thank you, friends, for reading this article till the end.