The Maclaren Quest stroller is a lightweight, compact and easy to manoeuvre double stroller that will provide parents with the perfect travel system for their newborn. This article will show you how to assemble the Maclaren Quest Stroller.
Steps on How to assemble Maclaren Quest stroller
Step One: Open the canister that holds all of your Maclaren Quest Stroller’s parts.
Step Two: Hold on to both handles and put them together, making sure they are facing each other with one handle at the top and the other below it. The two wheels should be pointing in opposite directions from each other – this is called a “T” shape.
Step Three: Push the two handles together to lock them into place and move on to Step Four.
Step Four: Remove the canister you just used from your Maclaren Quest Stroller, then open it up again so that all of its contents are now visible.
How do I remove Maclaren Quest stroller cover?
If you have a Maclaren Quest stroller, then there’s an easy way to remove the cover. You’ll need two hands for this: one hand on either handle of your Maclaren Quest Stroller with the canister in between them – like before, but with both handles facing down and not up).
Now bend at the waist and pull up on the cover, away from your body. The canister will come with you as it’s still locked in place to both handles of your Maclaren Quest Stroller.
How to Clean Maclaren Quest stroller
Cleaning instructions on Maclaren Quest Stroller:
Wipe clean with a damp cloth. Wipe dry, do not use household cleaning products or furniture polish which could damage the fabric and plastic. To remove stubborn stains, sponge with the diluted mild detergent solution as directed by manufacturer – never saturate! Rinse thoroughly to avoid residue build-up.
For best results, rinse in front of a sunny windowsill before drying out of direct sunlight to prevent discolouration from UV rays and natural oxidation of materials that will break down colours over time.
Don’t forget your seat pad! Remove it occasionally for washing (following the above directions) with soap and water/dishwashing liquid (no dishwasher!). Allow at least 24 hours to dry before reattaching it.
How to remove the front wheel of a Maclaren Quest
Step 1. Put down a towel or rug in case any parts fall off and they can’t be found again.
Step 2. Unscrew the grey cap on top where the handle meets the frame (about 45 degrees). There is an Allen wrench that comes with this step but it might not work if your screws are too tight so try any small screwdriver first before resorting to using a toolkit from home. Once unscrewed, set aside for later use.
Step 3. Unfasten two bolts holding up one end of the wheel arm by loosening them just enough that there is room for sliding out – be careful not to fully remove bolts from the holes yet.
Step 4. Move the wheel arm so that it is at a 90-degree angle with the frame and then loosen two bolts on the opposite side of the frame (about 45 degrees) enough for sliding out – be careful not to fully remove them from their respective holes as well.
Step 5. Remove the bolt by pulling away until there’s an opening in between which holds one end of the wheel axle rod; keep holding onto the other end while removing it from its place next to the grey cap unscrewed earlier, where the handle meets the frame.
Place aside with the first removed Allen wrench or screwdriver depending on what you used. Now freewheel will slide off easily without any resistance because you’ve loosened up both ends with your other hand.
Step 6. Lift frame of Maclaren Quest, and slide out both wheel axles from their respective holes on the opposite side (about 45 degrees) as you did with one end earlier; keep holding onto them close to where they meet together.
Now put aside the first removed Allen wrench or screwdriver depending on what you used for this job – it’s time to use a new tool! In its place is a hex key which now needs to get inserted into those two tightly screwed bolts on another side of the frame.
When turning the handle back and forth, be sure not to fully remove either bolt for the stroller frame not to lose balance; just loosening up should suffice at this point because there are no more obstructions.
Can I change the wheels on my stroller?
You may be able to change the wheels on your stroller. Please check with Maclaren’s website for specific details about what is compatible and available at this time.
Can I use my own car seat?
No, you cannot attach a different type of car seat than recommended by the manufacturer because it will not fit correctly and could cause injury in an accident or otherwise harm the baby.
It is also important that all safety features are followed when securing a child in their carseat – even if they’re using one purchased elsewhere. When purchasing any other product for your child, please make sure that it has been tested according to US Federal Motor Vehicle Safety Standards (FMVSS). How can we help you today?