The swivel soccer ball chair is a great buy for any soccer fan. The seat and back are made of one continuous piece of moulded plastic that can be easily assembled without the use of tools or screws. This blog post will show how to assemble a swivel soccer ball chair with arms in just five simple steps!
Steps on Assembling a Swivel Soccer Ball Chair with Arms
Step One: Connect the back of the chair to the seat using provided screws.
Step Two: Attach caster wheels and tighten bolts with a screwdriver.
Step Three: Place armrests at the desired height on the sides of the soccer ball, then attach them in place by rotating each one into slots until they click firmly into place.
Step Four: Insert screws to connect armrests and seat at the desired height, then tighten with a screwdriver.
Step Five: Set the chair on an even surface and adjust tilt tension by turning the knob clockwise or counterclockwise until you reach how much resistance you want from your swivel soccer ball chair with arms.
Step Six: To adjust how much resistance comes out of the chair when you swivel, turn the knob towards yourself or away from yourself to tighten or loosen tension respectively.
Note: Adjusting tilt tension will also change how far back the seat sits as well as how fast it rotates if desired; a tighter setting will cause the chair to sit farther away from you and rotate more quickly.
Step Seven: Once the tilt tension has been adjusted, set how much resistance comes out of armrests by turning the knob clockwise or counterclockwise until desired resistance is reached (this will also change how far back they push).
How do you replace the wheels on a chair?
Step One: Turn off the power and disconnect the outlet cord.
Step Two: Remove lower back pad, preferably using pliers or another tool that can cut through staples (can be found at most hardware stores). Once loose, tilt it away from the seat of the chair to make it easier to remove.
Step Three: Remove the screws holding the wheel in place, using pliers or another tool that can cut through staples (again, found at most hardware stores). Depending on how many there are and how they’re positioned, sometimes two may need a screwdriver while others only require your fingers.
Step Four: Disconnect the wheel from its metal stem, then repeat for all four.
How do you fix a wheel on a chair?
If one of the caster wheels on a chair is not rolling properly, it may be necessary to replace the wheel.
However, before replacing an individual caster wheel make sure that there are no other broken or missing parts and all bolts holding the casters in place are tight. If everything checks out then proceed with repairing by removing any old debris from the caster, then prying off the cap covering.
Remove any old or broken bolts and replace them with new ones if necessary. Once you have replaced all visible bolts, attach a replacement wheel to your chair’s stem by lining up the holes on the bottom of each piece together.
How do you lock the wheels on an office chair?
It is important to note how you lock the wheels before moving forward. For a fixed wheel, there will be two levers with one on each side of the chair. To unlock them push both down and then move them up to lock in place. To do this for swivel locks just flip it over so that they are facing downward and then follow the same process.
How do you protect hardwood floors from scratches?
Protecting hardwood floors from scratches can be done by placing a mat in front of the chair that is made for this purpose. If you don’t have these mats, plastic can also work or even cardboard with an adhesive applied to it if need be. It’s important not only how long your feet are on the floor but how often as well.
What are brakes for?
Brakes keep your chair from rolling when you want it to stay still or slow down how fast it moves. They are located in a variety of places on different types of chairs and will be mentioned below how they work for each type. For fixed wheel casters, there will be a lever on each side of the chair.
To unlock them push both down and then move them up to lock in place. For swivel locks, just flip it over so that they are facing downward and follow the same process.
How do you keep wheels from rolling on hardwood floors?
The best way to keep wheels from rolling on hardwood floors is by using a rubberized material called “no-skid tape” or “non-skid adhesive mat.” These products will create friction between the chair and floor so that they are less likely to roll. You can find these items online or at your local hardware store in the “hardware” section.