This how-to guide walks you through how to assemble a kolcraft bassinet, step by step. It’s easy to take the bassinet apart for storage or transport, but it will take some time and patience. The last thing you want is to put your baby in a dangerous product because you didn’t assemble it properly!
Steps on How to Assemble a Kolcraft Bassinet
Take all of the components out of their packaging and lay them on a table where they can be easily reached.
Step one: Check that all accessories are present before assembly begins If an accessory is missing or defective, contact customer service immediately. Put together mattress base Align support bars with side panels Place two clips at the top centre into slots Attach long ends of the mattress pad.
Turn cover right side out Pull tabs across corners until all four corners have been inserted. Slide mattress base into cover. Pull the tabs through all of the openings until you reach each corner; use your hand to push the fabric down and ensure a snug fit at the bottom.
Step Two: Attach bassinet stand Open both locking levers underneath bassinet support bars Locate holes in top surfaces of support bars Align latches with a hole on the underside of the bar.
Push latch up into the hole, then squeeze lever closed Repeat for opposite side Once attached properly, they should be sturdy enough that even light pressure causes them to close without popping open If not stable or secure, contact customer service immediately Place diaper changer pad where desired Be sure all pads are firmly attached before using baby’s products
Step Three: Place hood onto the front piece by aligning the back of the hood with the top edge Attach two metal dowel rods by aligning and sliding ends into rear holes on both sides Once attached, turn right or left to lock in place. Secure bassinet mattress pad onto bars.
Can you wash foam bassinet mattresses?
No, it is not safe to wash the Kolcraft bassinet mattress. It cannot be immersed in water or washed with any type of liquid soap as this may cause the product to become unstable and unsafe for your baby. Instead, brush away stains using a soft-bristled brush as needed and then wipe clean with a damp cloth followed by a dry cloth.
Avoid the use of abrasive cleaners which can damage foam cells causing them to collapse upon themselves leading to permanent indentations that are impossible to remove from the surface (Consumer Reports).
When removing soiled sheets, always lift sheet corners slowly from each side instead of pulling straight up off the top – otherwise, you risk tearing material seams where they connect at opposite edges below section High resiliency polyurethane foam is used in the seat portion of all Kolcraft bassinets.
This type of high density, durable material was chosen as it provides a firm and comfortable sleeping surface for your baby that can be wiped clean as needed without harming foam cells.
How to clean a bassinet hood
A small vacuum cleaner should do how to assemble kolcraft bassinets with ease, though there are other methods as well. Using an old toothbrush and soapy water can assist those who prefer natural or chemical-free cleaning products when caring for their baby’s items.
How to store a wicker bassinet
Wicker bassinet can be stored in either the original box or another container of your choosing. If you choose to store a wicker bassinet outside, make sure it is completely dry and place some mothballs inside for added protection against insects that may want to lay eggs within the cradle.
How to clean a baby’s mattress pad
Washing a baby’s mattress pad is easy, but you should always check the tag before putting it in your washing machine.
Step 1. Make sure to clean a baby’s bassinet with mild soap and water using either an old toothbrush or dish detergent for scrubbing away stains; remember that this can be used on both fabric and metal models.
Step 2. Avoid drying out a wicker bassinet by air drying outside if possible. You may also use low heat settings on high-quality machines when tumble drying. Always read manufacturer instructions before doing this so as not to damage them! If they still appear damp after being placed into the dryer, how to dry a bassinet safely can be helpful.
Step 3. If you have an older plastic baby crib, it is best not to try deep cleaning with harsh chemicals and scrubbing pads that are intended for newer models only. It’s best recommended to use warm water and mild dish soap.
What do you put in the bottom of a bassinet?
A diaper changer pad. The mattress should be placed on the bottom of a bassinet, and then you can add other items such as bedding or even toys to make it more fun for your baby.
How do you clean an old wicker bassinet?
A damp cloth or cotton swab dipped in soapy water should be used to clean the Wicker bassinet.
How do you clean the hood of a Graco bassinet?
Most often, cleaning the hood is as simple as wiping it down. If there are any stains on the fabric that refuse to budge, try using an old toothbrush and some warm soapy water instead. Be gentle when scrubbing because many fabrics may be susceptible.