Dryer Trip Breaker When Plugged In; 5 Surprising Reasons!

Do you know why the dryer trip breaker when plugged in? If not yet, then you have come to the right place. We are here to help you out. A variety of factors might cause your dryer tripping breaker troubles.

Most dryers usually have problems with the heating element, assembly, drive motor, or anything as basic as defective wiring or energy supply. 

dryer trip breaker when plugged in

Yes, my friends, it’s all true about it. Tripping the breaker creates many problems while you are drying the clothes. It’s critical to write down the reasons for the problem to resolve the difficulties. So, if you’re curious to know all about this topic, keep reading till the conclusion. Some of the most common issues and their solutions are detailed here. So without further ado, let’s get started!


Why Dryer Tripping The Breaker?

Figure out exactly why the dryer trip breaker when plugged in. This issue has occurred for a variety of causes. We’ve developed a step-by-step guide to aid you in resolving this problem below. Let’s dig them one by one.


#1. Faulty heating element

The heating element is the ideal point to begin. The heating element heats the air that circulates in your dryer. Whenever the heating element fails, the heating housing might short out, causing the tripping of your dryer breaker. To inspect the heating element, follow these steps: Switch off the dryer’s electricity. To work on the dryer, remove it from the wall socket.

Remove the dryer’s panels. Determine where the heating element is located Once you’ve found it, test each of the terminals on the heating element using a multimeter. The terminals must be connected to the enclosure. If there is continuity between the heating element and the casing, it is faulty and must be replaced. After replacing the part, reassemble your dryer and examine whether the issue was resolved. You can proceed to the next component if the heating element succeeds in the continuity test.


#2. Defective dryer motor

Before looking into your wiring for the source tripping of your cloth dryer when plugged in, you might want to look at your dryer’s internal processes. You may have a faulty motor if the dryer trips the breaker just after 10 minutes of using it. To inspect the dryer motor, follow these steps: Cut off the main power supply from your dryer. Remove the motor and use a multimeter to check for continuity. You’ll have to change the motor if there is a fault. Examining the bearings is yet another approach to inspecting the motor.

The bearings are for the interior components that keep your machine’s motors functioning smoothly. As a result, their significance in ensuring that your equipment runs appropriately cannot be overstated.  Your bearings may become blocked with dust due to prolonged usage, keeping the motor from achieving its usual operating speed. This leads the dryer to use greater electricity, potentially triggering a circuit breaker.


#3. Faulty terminal block

If you’re using an electric dryer, you can see a set of electrical lines connected to the terminal block. If either of these wires gets free, they may spark, causing a portion of the terminal block to be destroyed. Whenever this occurs, one of its wires might hit the dryer’s body, causing the dryer circuit breaker to trip. It doesn’t occur very frequently, but if you’ve checked all of the other parts above and still haven’t found anything, you must examine the terminal block. To accomplish this, follow these steps:

Track down the terminal block. Examine all of the wires to determine if any are frayed. If this is the case, tighten them up. Examine all the wires to determine if any appear to be arcing. If that’s the case, get rid of them. After that, you may turn on your dryer to see whether the problem is fixed. If the dryer continues to malfunction, go on to the other parts to inspect.


#4. Faulty thermostat

This one is a further inner part that may lead your cloth dryer to trip the circuit breaker regularly. A malfunctioning thermostat may suck in much more heat than planned, drawing in more current. As a result, a faulty thermostat might consume too much electricity, potentially overloading your breaker and, therefore, your dryer trip the circuit breaker. Your problem will be solved by replacing the thermostat with a new one. You may also be interested to know about installing a dryer thermostat.


#5. Faulty circuit breakers 

Whether your dryer continues to trip breakers after you’ve double-checked everything else, it’s time to see if it’s the breaker that would be triggering all of the circuit trippings.  A defective breaker might cause your dryer-breaker problem. Your breaker may not have been designed to manage quite an electricity-intensive gadget and malfunction. Use a digital multimeter to inspect the status of your breaker. Simply connect it to your breaker and verify the results to see whether it needs to be replaced.


It’s A Wrap!

We hope you’ve learned why a dryer trip breaker when plugged in after reading this article. The 5 major reasons for your dryer tripping the circuit breaker have been mentioned previously. You’ll figure out how to solve this problem if you read this article thoroughly. Friends, we appreciate your presence. Don’t hesitate to know these things too; read about what is eco dry on samsung dryer and how to switch from gas to electric dryer.

Leave a Comment